News for hackers. Stuff that matters.
Re:Finding Lead in Stanley's Quencher by doubloon on Sunday March 17, 2024 @09:20AM (#39734308)
I have the same problem with this as with retro youtubers using lead solder.

Consumers are not the only ones that matter

The people working in the factoriesare exposed to lead. The people at the mines are exposed to lead. The people in shuttered ghost towns like Pitcher Oklahoma are exposed to lead. The people transporting lead are exposed to lead. People working in recycling or waste management or landfills are exposed to lead. Lead is not good to put into the manufacturing stream or the waste stream. By continuing to create demand you are continuing to put lead in the environment in forms where it gets into humans and damages their brains.

Re:Finding Lead in Stanley's Quencher by rsaxvc on Sunday March 17, 2024 @11:12AM (#39734971)
You're eactly right. I saw the blight at Herculaneum, MO in the 2000s - dozers plowing down houses in a slowly expanding circle centered on the smelter.

1 in 5 students had excess blood lead. The schools nearby were scraped down and soil was replaced whenever the lead levels got too high from the dust blowing off the open ore and slag trucks running town. The smelter didn't hit EPA requirements for 25 years, and when faced with enforcement, decided to leave rather than produce lead cleanly, because it is not economical to do so cleanly. Cheap lead offloads the environmental and health effects to someone.

https://health.mo.gov/living/environment/hazsubstancesites/p...

https://www.kbia.org/science-and-technology/2012-08-08/the-e...

Re:Finding Lead in Stanley's Quencher by doubloon on Sunday March 17, 2024 @12:24PM (#39735562)
thats very interesting, i never heard of this, i wonder how many other towns are off-the-radar. and in China probably even more now.

i wonder if the EPA could be better off if it gave grants instead of fining people.

Re:Finding Lead in Stanley's Quencher by analog31 on Sunday March 17, 2024 @04:07PM (#39737580)
Superfund is such a a program.
Re:Finding Lead in Stanley's Quencher by jjtheblunt on Sunday March 17, 2024 @12:50PM (#39735789)
government handouts seem to escape their original purpose, famously.

For a recent example there are the covid relief scams galore. very often in the news the last year or two at least in Arizona, where some egregiously shameful people 'embezzled' and 'gamed' the grants system to buy super extravagent properties, etc. .

Re:Finding Lead in Stanley's Quencher by LargoLasskhyfv on Sunday March 17, 2024 @04:35PM (#39737814)
Doesn't have to be a smelter. Battery factory is enough. Like former VARTA, now Hawker, now closed (2021) in Hagen i.W., Germany.

Lead, so sweet, its dust a sheet, over kindergardens, parks and shools, the fools!

https://osm.org/go/0GMgy_p2J--?m=

Re:Finding Lead in Stanley's Quencher by frankharv on Sunday March 17, 2024 @09:38AM (#39734410)
Exposed to lead? Heck I machine it.

What do you think SAE660 bearing bronze contains.

This level of hype is horribly misguided.

I have not witnessed one machinist harmed by lead in 40 years.

If I cared I would wear a face mask when working with bronzes.

Truthfully Hexavalent Chromium exposure from stainless scares me more.

That is a known carcinogen and I machine alot of high Chrome content stainless.

Re:Finding Lead in Stanley's Quencher by pgcudahy on Sunday March 17, 2024 @09:51AM (#39734477)
"I have not witnessed one machinist harmed by lead in 40 years." Do you know what you're looking for? Lead poising can be subtle but eventually devastating. This is like the asbestos industry saying that miners didn't get harmed because they didn't follow up with them years later when mesothelioma slowly strangled them.
Re:Finding Lead in Stanley's Quencher by copperx on Sunday March 17, 2024 @10:02AM (#39734551)
I suggest you temper your gut feelings with a blood test for lead. It's $49 at Quest and you don't need a doctor's order.
Re:Finding Lead in Stanley's Quencher by msrenee on Sunday March 17, 2024 @12:40PM (#39735681)
It's interesting to me that there's so little public awareness about stainless steel as it affects workers. I'll go ahead and skip working with it as the piddly amount of a pay bump doesn't offset the known danger it poses. My nose has the correct number of holes in it, thank you very much. Add in the cancer risk and I've got no intentions of screwing around with the stuff.
Re:Finding Lead in Stanley's Quencher by ShitHNsays on Sunday March 17, 2024 @11:53AM (#39735297)
Well well well, life's a tragedy. Better get used to that sooner than later.
Re:Finding Lead in Stanley's Quencher by wakawaka28 on Sunday March 17, 2024 @01:34PM (#39736211)
That retro Youtuber gripe is silly. You really think it's worth getting bent out of shape that one guy is using a little bit of lead solder to repair a valuable antique thing full of lead solder and thus keep it out of the landfill? They want to use it for technical reasons. There are many more significant sources of lead than oddball hobbyists, such as aviation fuel. Technically most hazardous chemicals we ever use end up in the environment. Even medication. So getting too fixated on a rare specialist use of lead is misguided. We should reduce the uses of lead and other toxic materials where possible, but sometimes it isn't possible or economical.
Re:Finding Lead in Stanley's Quencher by kortilla on Sunday March 17, 2024 @03:31PM (#39737262)
Av gas is what has led, not jet fuel. Av gas consumption is negligible by comparison so it’s not the impact you think.
Re:Finding Lead in Stanley's Quencher by wakawaka28 on Sunday March 17, 2024 @03:38PM (#39737330)
Literally tons of aviation fuel vs. trace amounts of fresh lead solder. I think the fuel is obviously worse. Neither one may be so bad that it needs to draw excess concern of course.
Re:Finding Lead in Stanley's Quencher by kortilla on Wednesday March 20, 2024 @01:51AM (#39763220)
Stop saying “aviation fuel” when you specifically mean the thing with lead. Aviation fuel is a generic category that captures jet fuel and other lead free variants.

It makes it sound like you don’t know what you’re talking about because you’re making an incorrect statement about a general category.

Re:Finding Lead in Stanley's Quencher by Brian_K_White on Sunday March 17, 2024 @02:12PM (#39736576)
"You really think it's worth getting bent out of shape that one guy is using a little bit of lead solder to repair a valuable antique"

Yes.

Not even close.

As someone who repaires such things myself, I know that there is no excuse for it.

Simple as that.

I do it myself and so I know just how not-a-problem it is.

Several lead-free solders are perfectly usable in all the same places, and the only way to reduce the background radiation of lead permeating the entire environment, is to stop putting it into the environment.

Keeping the antique radio out of the dump does not excuse the fact that the same user had to buy a spool of lead solder which had to be manufactured, and at least half of that spool will go right into the environment, not into museum exhibits.

It will be in spatters and sponges and wicks and soldapults and brillo scrubbers and random junk scrapped wiring and junk projects that are not antique radios housed in museums forever. Probably 90% or more of that spool ends up all over the environment rather than in some precious artifact.

Yes the lead-free solders are slightly more difficult to work with, but hardly enough to matter. If you never soldered anything before, the very act of soldering successfully at all is a baffling art to a lot of people. After some amount of trial & error, maybe training if they're lucky enough to know someone, they eventually develop a feel and a sense for how to get it to work right. Going from lead to lead-free requires a similar adjustment, but it's a freaking microscopic fraction of the difficulty.

Complaining about lead-free solder is nothing but pathetic baby crying, and crying over something that is simply not that difficult, and something that comes at a simply inexcusable cost.

Re:Finding Lead in Stanley's Quencher by bxparks on Sunday March 17, 2024 @03:21PM (#39737190)
You have strong opinions on the use of leaded solder. I'm curious if you have some numbers to drive home your point. For example, what is the relative risk of using leaded solder for a hobbyist creating a handful of prototype circuit boards a year (using proper ventilation of course), versus living close to an airport exposed to burning jet fuel which contains lead to this day? I want to know, roughly speaking, if using leaded solder a few times a year cause 100X more exposure or only 1/100 the exposure compared to living near an airport. If it's only 1/100 compare to an airport, I'm not going to worry about it. If it's 100X, then I think your position is quite valid. [Addendum: Another example, what is the risk of leaded solder compared to lead exposure from common household items like brass knobs, handles, fixtures, and keys?]

My current inventory of solder was obtained from estate sales, so they are all leaded, but old stock, not newly manufactured. If I had not bought them, they would have been thrown away into the garbage dumps.

Re:Finding Lead in Stanley's Quencher by mauvehaus on Sunday March 17, 2024 @03:35PM (#39737301)
Jet fuel does not contain lead. Jet fuel is for practical purposes roughly the same part of the dinosaur juice as kerosene and diesel. Jet fuel is burned in turbine and turboprop airplane engines, which comprise the enormous majority of the commercial fleet.

Avgas is the stuff with lead in it. Avgas is basically gasoline with lead added as an anti-knock agent and is burned in reciprocating spark ignition engines. Typically these are found in the general aviation fleet.

Re:Finding Lead in Stanley's Quencher by Brian_K_White on Sunday March 17, 2024 @07:43PM (#39739073)
A simple observation that cannot be refuted because it's an already accomplished fact that I have no problem soldering with 305 (or anything else really) is not a strong opinion.

All anyone can say is that maybe I'm lying or maybe don't know what a good job looks like and so don't know I'm actually having problems. Or maybe I only ever tried within a narrow sliver of ideal situations and conditions. We will all just have to grant each other some basics like that or else there's no point in conversing at all.

But it's farcical me to say "I use it all the time and it's fine." and respond "You're wrong."

Really? I didn't just do the thing I just watched my hands do right in front of my face? This project in my hands is not actually soldered? And doesn't actually work? Am I in an Elon Musk simulation or something?

My physics are not different from your physics. My sac305 is not different from your sac305. My 300-350 degrees c is not different from your 300-350 degrees c.

Such basic implacables are not a "strong opinion"

But, it's true that, having examined the basic facts and tried things myself, I have now arrived at a conclusion that is a rather strong opinion that the crybabying is nothing more than that. 63/37 is a little easier and that's all there is to that.

Re:Finding Lead in Stanley's Quencher by bxparks on Monday March 18, 2024 @12:24AM (#39740511)
Are you sure you are replying to correct post? Some people in this thread are resorting to name calling. That is unfortunate, but that's not me.

All I wanted was a sense of the relative risk of leaded solder compared to the other sources of lead around me. That's all. I figured that someone with such strong opinions as yours would have that sort of information.

I have no opinions regarding the ease of use of leaded solder versus unleaded solder. I actually don't know what sac305 is... Google tells me it's 96.5% tin, 3% silver, and 0.5% copper.

Re:Finding Lead in Stanley's Quencher by Brian_K_White on Monday March 18, 2024 @05:19PM (#39750161)
Ok sorry.

Yes sac305 is a common lead-free solder. It's not easy to replicate the properties of lead-tin alloy, so there are a lot of different alternatives and none of them really work quite as well.

There's 2 classes of problem: usability and functionality. Lead-free is both a little more difficult to use, and then is a little more likely to fail over time.

Usability: The usability problems are 2 things, higher temperature, and surface finish.

In the best case with old lead-tin, you still have to develop a skill to get in and get out relatively quickly and not keep the heat on for a long time. Even the relatively lower old temperatures are still hot enough to destroy most components and the pcb traces if you lay the heat on for extended times.

But all of the lead-free alternatives require a little bit higher temperature, and so there is a smaller window of time to goof off and blunder around with the heat on. Smaller but still easy enough. A datasheet for a component might say something like max 300c for 3 seconds, but really you can poke around for 30 seconds at 350. 30 seconds is forever. If you can't get it done by then, the problem isn't the solder.

The surface finish matters because in the old days it just so happened that you could be a cave man and still know if you made a good joint or not simply by the surface finish. If it's shiny, it's good (probably), if it's dull, it's bad. sac305 usually cools to a dull finish even if everything is perfect. You can still tell if you made a good or bad joint, it's just not as utterly black/white simple as before.

Both of those are just, it's a little more difficult. Still perfectly doable and not just by some wizards and not by most mortal humans.

Funcionality: The most valid problem is the performance, where after doing the sufccessful soldering, the solder fails in some way later on.

sac305 and most others are generally a little less ductile and prone to crystalization and fatigue cracking, and the biggest problem is tin whiskers.

sac305 is pretty much the worst for growing tin whiskers. On fine-pitch legs on surface mount parts the pins are close enough together that in bad enough environmental conditions, whiskers can grow to short between two pins eventually.

But, it takes particular conditions and doesn't usually happen to most ordinary things kept in ordinary indoor environments, and if you're building something that has fine pitch parts and you know it will be used on a boat or something you can mitigate that by adding a coating, and lastly in this case, point-to-point wiring in an antique radio is way too large to have any tin whisker problem. Whiskers grow to something like 500um in the worst case. It takes both a bad environment (presumably and "antique radio" will be protected and not used on the deck of a saltwater fishing boat) and requires parts that are almost touching each other. Antique radios don't even have PCB's. Medium-old electronics that havs pcbs but through-hole parts are maybe barely subject to whiskers. It will be uncommon for a whisker to reach all the way between 0.1" (2.54mm) chip legs, but not impossible.

These things are certainly problems. That's true. Yet it's also true that most electronics have been using nothing but this stuff for almost 20 years already by now.

There has been exceptions allowed for specialized things where the functionality and performance of the lead alloys was necessary enough to outweigh the environmental impact. But they are about to remove a lot of those exceptions soon. It is a problem, but it's not a problem for any hobbyist.

This subthread, my reaction, was exactly about the suggestion about "some retro guy repairing an antique radio". That guy absolutely not even close has any need for lead solder, and yes, that one guy using it does poison the environment, because there is no such thing as one guy. It's countless guys. If one guy can buy and then use something, then so can everyone else. And for every one of those users, theyr aren't just soldering a few joints one time. They have 1lb spools of solder and ALL of that solder eventually winds up in the ground and leeching into the water and soil. Most of it actually gets turned into fine dust because that's what happens when you clean the tip, which you have to do continuously, and when you desolder something, the vacuum atomizes the liquid solder as it's being sucked out of the via.

That's why it's so bad. There's no such thing as just one guy doing it, and for every one of the people, imagine taking a pound or two of lead (solder isn't 100% lead, but a single person will posess a few pounds or more total of different solders) and imagine say 10% of that lead being actually in some project. Then another say 30% being in the form of little bits and pebbles and the size of a bb and discarded joints like bits of soldered wiring cut off and discarded, and the rest, say 60% all in the form of particles the size of sand all the way doewn to very fine dust. And all of that solid pound of finely ground pebbles, sand, dust, ends up just everywhere, only some ends up in the local dump. a lot ends up just in the structure of the house and the ground under and around it right near wherever the work bench is. When you sweep and vacuum your work area, you are not remotely actually recovering all that lead dust.

And the next family to occupy that land didn't sign up for that.

When I say "no excuse" I mean that, there is no overriding need that justifies it. Sure lead-tin works better both while using it and then klater for the life of the object, but it doesn't work better enough, and for most people the application isn't critical enough, for that to outweigh working towards the goal getting led out of the environment.

Unleaded gasoline is way more difficult to use and less performant and has cost everyone billions, and we all shouldered that burden, only so that some man-baby can undo that very difficult and costly work just so they can solder a wire in a radio a teeny little bit easier?

No. The two considerations don't compare at all. It's just that one is easy to see and one is not so easy to see. One you can see with your eyes right now and gives you immediate gratification, and one you have to see with your mind, and you have to care about anything but your own convenience as the single most important consideration above all others.

Re:Finding Lead in Stanley's Quencher by jki275 on Sunday March 17, 2024 @04:19PM (#39737679)
Sorry, but as someone who has had to use them, lead-free solders are garbage. They are difficult to work with, require higher temperatures to use, don't last as long, whisker and destroy equipment they're used in.

This is all well known, it's not a mystery, and lead in solder is the least of the problems with lead in the world today.

Re:Finding Lead in Stanley's Quencher by exmadscientist on Sunday March 17, 2024 @05:10PM (#39738080)
If all you've used is crappy old SAC305 lead-free solder, you owe it to yourself to try a modern alloy like SN100C (& friends, it has several names and similar competitors). It's generations newer and with the right flux (I like AIM's Glow Core wire) it's just great for routine work. It runs a little hotter, but most people already solder too hot anyway, so who cares.

I still use 63/37 or 62/36/2 for anything challenging, though. Or for old rework: many people in this thread are missing that you really, really shouldn't mix alloys on a joint, so you've got to get the old stuff out before switching to lead-free, and at single-joint scale that's a lot more polluting than just grabbing the spool of 63/37.

Re:Finding Lead in Stanley's Quencher by jki275 on Sunday March 17, 2024 @05:21PM (#39738162)
I'll definitely agree that you shouldn't rework old joints with different solder.
Re:Finding Lead in Stanley's Quencher by Brian_K_White on Sunday March 17, 2024 @07:18PM (#39738952)
How come I have no problem? Even with plain old sac305 let alone the supposedly nicer ones.

From big old chunky point to point, to manually drag soldering 0.5mm pitch tssop.

I have no problem doing something that you claim is impossible or too difficult, and somehow this makes me the crybaby?

Ok.

Frankly if it was me I wouldn't be so keen to tell everyone how weak and incapable I was.

I grew up on leaded as we all did. I used to really like the radio shack 0.015in 62/36/2 silver bearing. Did indeed work very nice.

And yet after an inconsequentially short maybe a single hour of effort, I was able to adjust to 305.

You telling me I'm just better than you? Well if I'm just better, then shouldn't you be listening instead of arguing? If I'm not better, then how do you explain my lack of difficulty with something you claim is difficult?

Re:Finding Lead in Stanley's Quencher by jki275 on Sunday March 17, 2024 @10:37PM (#39740064)
You're putting a whole lot of words in my mouth and setting up a whole field of straw men there. Good luck with that.
Re:Finding Lead in Stanley's Quencher by wakawaka28 on Sunday March 17, 2024 @02:49PM (#39736901)
I think nobody craves lead in their life. So if these hobbyists say they need it, I'm siding with them. The usual argument is that lead solder flows better at low temps.

>Going from lead to lead-free requires a similar adjustment, but it's a freaking microscopic fraction of the difficulty.

Once lead is used on an item, it may be inadvisable to use anything but lead. It's not only harder and more expensive to switch but using anything but lead-free where lead is required/preferred will probably produce more e-waste.

>Complaining about lead-free solder is nothing but pathetic baby crying, and crying over something that is simply not that difficult, and something that comes at a simply inexcusable cost.

You're the one pathetic baby crying about mere grams of lead in niche applications here. Your "inexcusable cost" complaint is subjective. I bet you produce a ton of garbage and toxic waste just living your ordinary life that someone in the world would consider inexcusable.

Re:Finding Lead in Stanley's Quencher by mordechai9000 on Sunday March 17, 2024 @06:06PM (#39738489)
I don't think we should be resorting to calling each other crying babies over this. I recognize that you were not the first.

> I think nobody craves lead in their life.

Plenty of people scoff at the idea that handling lead is risky, whether it's fishing weights, ammunition, or lead solder. I've watched a trained engineer use his teeth to crimp lead fishing weights. He said there wasn't enough exposure to matter, and people had been doing this since before he was born. Is he right? I dunno. I personally want every brain cell I can muster.

Re:Finding Lead in Stanley's Quencher by wakawaka28 on Sunday March 17, 2024 @06:52PM (#39738781)
Yes, I just said it was petty to single out hobbyists who use a few grams of lead for a good purpose as if they are killing the planet. That is a hysterical take, and he got more hysterical when I called him out on exaggerating, not knowing what he was talking about, and most likely being a hypocrite. The lithium battery in each of our phones is probably more polluting than an average hobbyist's lifetime allotment of solder.

>Plenty of people scoff at the idea that handling lead is risky, whether it's fishing weights, ammunition, or lead solder. I've watched a trained engineer use his teeth to crimp lead fishing weights. He said there wasn't enough exposure to matter, and people had been doing this since before he was born. Is he right? I dunno. I personally want every brain cell I can muster.

Everything has costs and benefits. In many applications, there are no suitable alternatives to lead, or else the alternatives are scarce and expensive. As a society we have eliminated most excess lead so I think further browbeating over it is silly. Virtually every car has a lead battery, most brass has some lead in it, but otherwise it is scarce in most households. Ammunition is one case where lead is potentially dangerous, but if you need ammunition then the mild precautions necessary to handle the lead are well worth it.

Re:Finding Lead in Stanley's Quencher by LM358 on Sunday March 17, 2024 @06:04PM (#39738476)
You are aware that leaded solder is in use in many industries to this day?

I'm soldering with SN62 now as we speak.

Re:Finding Lead in Stanley's Quencher by Brian_K_White on Sunday March 17, 2024 @07:21PM (#39738969)
You are aware that this means, validates, invalidates, nothing?
Re:Finding Lead in Stanley's Quencher by doubloon on Wednesday March 20, 2024 @04:45AM (#39764058)
The tiny amount of lead they use is inversly proportional to their social influence, they are literally called influencers, and they are influencing an entire generation to be indifferent to use of lead in electronics because the personal risk is easily mitiigated. None if them discuss the social or environmental risk , as if these disasters like Pitcher didnt happen or dont matter
Re:Finding Lead in Stanley's Quencher by skybrian on Sunday March 17, 2024 @06:25PM (#39738625)
As with anything in the manufacturing process, it depends how it's done. You can imagine it being done safely or dangerously, but either way, it's not a fact, it's something you imagined.

Unfortunately, we usually don't know what safety procedures were followed or whether they're adequate. This requires insight into the whole supply chain.

So, maybe it's better to be safe and ask for alternatives? But we don't know if it helps, because there are other materials and other reasons why one manufacturing process might be better than another.

Consumer purchase decisions are a very indirect way of affecting working conditions and a poor substitute for work-safety regulations.

Re:Finding Lead in Stanley's Quencher by bobmcnamara on Sunday March 17, 2024 @08:52PM (#39739492)
Must not be from the midwest.

Gilman and Pitcher closed because the cities could not be decontaminated.

The Doe Run plant outside Saint Louis closed because they couldn't refine clean lead economically. Much of the city around it was bulldozed off and buried.

There's a difference between "we don't what safety procedures were followed" and "there's no such thing as clean lead".

Re:Finding Lead in Stanley's Quencher by mikewarot on Sunday March 17, 2024 @07:52PM (#39739118)
Soldering doesn't involve boiling the lead in the solder. I worry more about the fumes from the flux than I do the solder. I just wash my hands afterward to make sure I don't ingest traces of it.
Re:Finding Lead in Stanley's Quencher by SomeoneFromCA on Monday March 18, 2024 @09:00AM (#39743801)
Yeah, well standard drivel from lead soldier connoseurs. The flux used for tin-bismuth or tin-germanium solders is exactly same. No point to perpetuate extraction of poisonous substances.
Re:Finding Lead in Stanley's Quencher by mikewarot on Monday March 18, 2024 @11:27AM (#39745842)
So you want me to remove all the lead/tin solder from the stuff I'm repairing... and do WHAT with it, exactly? I've been using the same roll of Kestler fine solder since the I got it about 20 years ago at the Dayton hamfest. I'm not exactly a bulk distributor of the stuff.

The ad-hominem attacks are un-called for. I was merely pointing out that the other used of lead involved boiling them off... and thus the lead was far, far more likely to go EVERYWHERE as a result.

Re:Finding Lead in Stanley's Quencher by SomeoneFromCA on Monday March 18, 2024 @11:50AM (#39746144)
"20 years ago at the Dayton hamfest". yeah explains a lot.

There is a lot animosity from older gen EEs towards lead free solder, lot of lies as the flux is more poisonous etc., however the point is in fact is not only personal harm, but reduction of consumption of lead at first place. The less lead is produced and thrown away the better.

Re:Finding Lead in Stanley's Quencher by mikewarot on Monday March 18, 2024 @06:49PM (#39750992)
So you agree I should just keep using the supplies I already have?
Re:Finding Lead in Stanley's Quencher by mikewarot on Monday March 18, 2024 @09:27PM (#39752097)
Ok, so I'll keep using my old solder, and buy the new stuff next time I need more solder. (Unless of course, someone gives me more of the old stuff before then, in which case its best to use it, and keep it away from the landfill)