There aren't that many "somewhat competent" DIYers with appropriate milling equipment and skills. It's a lot easier to 3D print a design than use manual tools to precisely manufacture something. Making it easier to kill people usually means more people get killed. A basic observation in criminology.
Obviously 3D printed guns are getting produced and are being used in crimes. The article also says that Canada has a bigger problem with guns smuggled from the US.
A gun is a tube and a pin. No milling is required.
The article is about Canada. And apparently there is a niche for some people who'd rather produce and sell 3D printed guns than "tubes and pins". And I pointed out some of the reasons. A 3D printer reliably produces parts that are quite precise with a lot less effort. That is worth a lot of tradeoffs, even if traditional craftspeople scoff at the properties of the plastic.
On HN there will always be people nitpicking on every detail left out...
While this is true for 100% printed guns, most fosscad folks will have core components that are metal. Barrels, firing pins, etc will be metal in most designs.
Some folks claim their guns can shoot thousands of rounds with no issue.
> They will have very poor accuracy, it won't be possible to rifle the barrel on a 3d printed gun in a way that will spin the projectile.
Folks literally etch their gun barrels with the same specs as commercially available barrels. Here is one such example from the /r/fosscad community: https://www.reddit.com/gallery/106u7au
While the fear is mostly media driven, the stuff folks are making now is a little alarming. Claymores, grenade launchers, etc. If you are interested in learning about this community, check out /r/fosscad on reddit.
For context, I have an AR with a printed lower that I've put ~1k rounds through without issue. In the US that's the only serialized part, and therefore the only part that would be typically purchased from a dealer and able to be "traced".
> Folks literally etch their gun barrels with the same specs as commercially available barrels.
I've made a couple of pistol barrels with ECM, and they're no less accurate than commercial stuff.
It might be interesting to know that I made those specifically in order to comply with US law - not to "evade" it. Even a single-shot rimfire pistol falls under the National Firearms Act unless it has a rifled barrel. It would have been much simpler to just use a metal tube, but I didn't want to deal with filing the forms, paying the tax, and waiting months for approval before putting together a random project that I started on a whim.
That's a bit of a stretch. I think you and a lot of other people underestimate how expensive it is. The people actually doing this are doing it just because they can. Still easier, faster and cheaper to buy a ghost gun in a state with more lax rules.
Plus in 99% of shootings the targets are fairly short range where rifling isnt even very important.
That's not my experience at all.
You have to have a means of rotating the button rifling tool consistently as it is pulled through the bore - for an m1911, probably the most common .45 ACP pistol, that's 1 revolution per 16" of barrel.
Because it will take multiple passes to cut the rifling, you'll also need a way to index the tool for each pass.
> Plus in 99% of shootings the targets are fairly short range where rifling isnt even very important.
If you're making a gun to shoot someone, that makes sense. The far more typical case is that you're making it because you are interested in making a gun, and rifling is a requirement in the US to comply with federal law for a pistol[1].
1: The term "pistol" is legislatively defined, but broadly speaking it's anything designed to be fired with one hand and <26" in overall length.
The reason rifling machines do it is to ensure minimal wear on the die, and for speed of operation but that's an optimization more than a requirement. This is also the reason why the cutters on a typical button are as long as they are: to ensure that it rotates.
You also don't need to index it for the same reason: the tool will seek the grooves made by the previous pass.
It's basically just a very coarse inside thread cutter, where the thread is so steep that it will drive the tool to rotate much as the bullet will rotate when passing through. This will work with any thread that is more than 1:1.
>it's most likely going to only work once or twice before it blows itself apar
LMAO see FGC-9.
>it won't be possible to rifle the barrel on a 3d printed gun in a way that will spin the projectile.
But it is possible to 3d print a mandrel for ECM machining, in a way that basically anyone can easily rifle for very low cost. See ECM machining guide as part of FGC-9 build. This sounds complicated but in practice very simple, print the part and attach a pipe along with pumped water/electricity and you get very nice accurate rifling tested to perform about as well as glock oem barrel.
>It would probably be better than a 3d printed one too.
Not typically at least using the most popular expedient arms manuals. The magazine and feeding typically performs much poorer than say modern 3d printed like FGC-9. Repeatable in-tolerance magazines/feeding have always been the weak point of most home machine shop made stuff and 3d printing has mostly solved that problem.
Recommended reading:
- Most countries that have gun control, have strict control of ammunition. It may be possible to 3d print a "gun", but it is going to be hard to find ammunition for it, unless you go the home made route for that too.
- Domestic or hobbyist 3d printing is not going to produce a particularly strong gun, it's most likely going to only work once or twice before it blows itself apart. There is a good chance the person using it will significantly hurt themselves.
- They will have very poor accuracy, it won't be possible to rifle the barrel on a 3d printed gun in a way that will spin the projectile.
- You don't need 3d printing to make a rudimentary gun, one can be fabricated relatively easily by a somewhat competent DIYer in a home workshop. It would probably be better than a 3d printed one too.
The point is, the arguments around 3d printed guns are mostly media driven, if someone is intent on hurting someone else, they will find a way to do it. 3d printing or the availability of designs is not enabling that.