News for hackers. Stuff that matters.
Re:Everything with a battery should have an off switch by ggm on Monday May 09, 2022 @04:56AM (#31311951)
I think this is special pleading. At the volume we're discussing a surface mount flow solder on off device is not going to kill the BoM, and could be designed not to be ugly.

It's no different to any other bad design. It could be better.

All phones and computers can be completely powered down. They're hardly ugly switches.

Re:Everything with a battery should have an off switch by abofh on Monday May 09, 2022 @05:19AM (#31312091)
Ermm, most phones and computers cannot be completely powered down. Either by nit-picking (CMOS clocks) or soft-switches (ACPI, soft button power-on), there's always some voltage in the system unless your PSU comes with an actual hard power switch (and even then, again, CMOS).

They consume a lot less power, but leave an 'off' phone in a drawer for a month starting at 100%, it will not be 100% when you 'turn it on'.

Re:Everything with a battery should have an off switch by JoeAltmaier on Monday May 09, 2022 @07:50AM (#31312995)
In low-power mode even those microcontrollers are using just nA (yes that's nano-Amps). Vs 100's of mA in operation. So the battery life goes from hours to what should be decades.

I'm thinking the battery goes dead because of leakage currents through the rest of the circuits, which were probably not designed to the nA standard.

A solid-state Off switch would also need a good silicon device to cut current consumption at the battery. Which also costs something.

Re:Everything with a battery should have an off switch by unwind on Monday May 09, 2022 @05:42AM (#31312200)
I understand and agree, but the use-case is a bit skewed since that's not even true for a bare "naked" battery or cell.

They all self-discharge [1], some chemistries more than others of course but phone batteries certainly do.

[1]: https://en.wikipedia.org/wiki/Self-discharge

Re:Everything with a battery should have an off switch by Retric on Monday May 09, 2022 @07:30AM (#31312862)
Self discharge is easily an order of magnitude slower than the power draw of these devices while seemingly off.
Re:Everything with a battery should have an off switch by throw10920 on Monday May 09, 2022 @11:10AM (#31315082)
> I think this is special pleading.

This is an emotional, low-quality response to what is a measured comment actually providing nuance to the discussion.

The parent poster is very clearly not saying that leaving off the power switch leads to a better experience for the consumer - they're just giving legit reasons that a design/marketing team might use to justify doing so. Please don't try to cheapen the knowledge that they provided like this.

Re:Everything with a battery should have an off switch by IIsi50MHz on Monday May 09, 2022 @07:42PM (#31321386)
I took it as "I think the reasons given are not legitimate, and are poor excuses for 'maldesign'.".

Where 'maldesign' is my dad's favourite word for every seeming design flaw or 'unreasonable' limitation. (-:

Re:Everything with a battery should have an off switch by m_eiman on Monday May 09, 2022 @05:14AM (#31312059)
> All phones and computers can be completely powered down. They're hardly ugly switches.

iPhones (and I assume most Androids as well) can't be completely powered off. Neither can Macbooks. In fact, I'd guess that most modern digital things with non-replaceable batteries can't be powered off.

Re:Everything with a battery should have an off switch by bombcar on Monday May 09, 2022 @09:01AM (#31313501)
There’s a specific Dell laptop reset procedure that requires you to open the case and disconnect the battery so you can then press and hold the power button to get it to discharge all residual power. It’s a pain.
Re:Everything with a battery should have an off switch by jasonthorsness on Monday May 09, 2022 @10:39AM (#31314582)
I had to do this a couple of times with a Lenovo that sometimes locked up completely when it went to suspend - battery was highly inaccessible so it was a 30 minute tense process each time - firmware update eventually solved the problem. Not sure what the solution for this is - something like one of those paper clip reset holes?