News for hackers. Stuff that matters.
Re:Building an RFID Proximity Card Cloner for $30 by gvb on Sunday January 02, 2011 @09:29PM (#2061861)
Hmmm, how effective is aluminum foil in blocking the RFID? Despite having "RF" in the name, the signal is primarily magnetic induction.

One google hit says "helps a lot, but doesn't prevent": http://www.omniscienceisbliss.org/rfid.html Note that the picture of the reader and the unshielded read distance (18") indications it is the long distance version.

I'll have to experiment at work tomorrow. ;-)

Re:Building an RFID Proximity Card Cloner for $30 by tgflynn on Sunday January 02, 2011 @09:34PM (#2061867)
Electromagnetic signals are attenuated exponentially in metals with a frequency dependent decay constant called the skin depth. The formula is given in this wikipedia page :

http://en.wikipedia.org/wiki/Skin_depth

If you know what frequency RFID uses and the thickness of the foil you can easily calculate how much attenuation you'd get.

Re:Building an RFID Proximity Card Cloner for $30 by gvb on Sunday January 02, 2011 @10:02PM (#2061922)
125KHz => 0.024mm skin depth

Looks like typical aluminum foil is thicker than that. The box in our kitchen doesn't say how thick it is, but the Wikipedia page indicates it is likely thicker than 0.025mm since it needs to be thicker than that to be impermeable to oxygen and water.

Ref: http://en.wikipedia.org/wiki/Aluminium_foil#Properties

Re:Building an RFID Proximity Card Cloner for $30 by tgflynn on Sunday January 02, 2011 @10:22PM (#2061959)
Hmm, one of us is off by an order of magnitude, I get 0.24 mm.

For Al foil thickness I'm seeing conflicting numbers from 0.2 to 1.1 mm. If my cheap digital micrometer hadn't died I'd measure some.

If my skin depth is right then the attentuation probably won't be complete, if yours is then it might nearly be. Of course that's only the case if the receiver and/or transmitter is completely wrapped. Although at low frequencies like that you could probably tolerate quite a large gap.

Re:Building an RFID Proximity Card Cloner for $30 by Deadsunrise on Monday January 03, 2011 @03:23AM (#2062584)
It can't be 0.24mm, that would be too thick. On the wikipedia page there's a picture that says: A roll of aluminium foil, with micrometer showing a thickness of 0.013 mm (0.00051 in)

http://en.wikipedia.org/wiki/Aluminium_foil

Re:Building an RFID Proximity Card Cloner for $30 by gvb on Monday January 03, 2011 @08:34AM (#2063059)
You are right, 0.24mm. I did the m->mm conversion in my head (d'oh).

My cheap digital micrometer only has two digits of precision in mm mode. Measuring my cheap (not "heavy duty") aluminum foil is at the limits of its resolution, 0.01mm.

Re:Building an RFID Proximity Card Cloner for $30 by tgflynn on Monday January 03, 2011 @11:44AM (#2063671)
I folded a sheet of heavy duty foil into 16 sheets and tried to measure the thickness and it was still << 1mm, so I think your estimate of about 0.01mm is reasonable.

In that case I would predict that a single sheet would have little affect on an RFID device operating at 125kHz. Note however that RFID devices appear to span a very large frequency range :

http://www.rfid-handbook.de/rfid/frequencies.html

and the foil would certainly block the higher frequency devices.

Re:Building an RFID Proximity Card Cloner for $30 by gvb on Monday January 03, 2011 @12:39PM (#2063914)
Experimental evidence, sample size of 1: a single layer of ordinary aluminum foil completely enclosing the card prevents a "normal distance" (4" square) reader from reading my card.
Re:Building an RFID Proximity Card Cloner for $30 by tgflynn on Monday January 03, 2011 @01:44PM (#2064148)
Another thought: is it possible there's exposed circuitry on the card that the foil is shorting out ? You could try wrapping it with a plastic bag before enclosing it with foil.
Re:Building an RFID Proximity Card Cloner for $30 by tgflynn on Monday January 03, 2011 @01:00PM (#2063983)
Are you sure it's a 125 kHz device ? Maxwell has never failed me before.
Re:Building an RFID Proximity Card Cloner for $30 by gvb on Monday January 03, 2011 @01:43PM (#2064143)
No, I'm not sure, but it does physically match the cards and readers in the article.

With no foil, the badge is read at 3-4".

With a single slice of foil ~18"x12" held in front of the sensor, the badge is read at ~1" (a noticeable reduction in signal).

With the foil folded in half and the badge in the fold so that it forms a single layer on both sides of the card, it was effective (could not read the badge).

With the badge in an aluminumized mylar antistatic bag, there was no evidence of a signal reduction (read at full distance).

I would theorize that Maxwell hasn't failed us, but the signal is weak enough that the foil attenuated the signal sufficiently to disrupt reading. The RFID reader works by modulating the sensor tuned loop by detuning on/off, which is going to be a pretty weak signal.

Re:Building an RFID Proximity Card Cloner for $30 by tgflynn on Monday January 03, 2011 @02:13PM (#2064296)
The read range you're seeing also seems compatible with a low frequency device.

I'm quite perplexed. I don't think the foil could be attenuating the signal directly. It might be reflecting it/altering the field pattern so as to reduce the effective gain between the transmitter and receiver antennas.

Re:Building an RFID Proximity Card Cloner for $30 by fr0sty on Monday January 03, 2011 @10:23AM (#2063346)
Protip: stack X sheets of foil on top of each other, measure, divide by X.