Proper valve spring design is hard: it's a balancing act between power consumption at the low end and power production at the high end. F1 engines have a (relatively) narrow operating band, whereas a road car is expected to be usable from (a low) idle to redline.
(Expense is less of an issue here. Multi-million-dollar supercars with 20,000 RPM redlines would sell well.)
Sorry to be a buzzkill but this is not correct
The engines are not camless. However, they are 'spring less' in a traditional sense. In the early 1990's the typical wound wire springs were replaced with pneumatically charged cylinder that functions as the spring. The reason was do to the inability to create wound wire springs that did not encounter harmonic issues as RPM went up and a more efficient valve closing action. However, through all of this, the camshaft itself is retained.This allowed engines to reach over 20k rpm (which sounds unreal) but the current regulations, introduced in 2014, limit them to 15k and they typically run less due to rules that limit fuel flow at higher RPMs.
The Koenisegg on the other hand is absolutely camless technology they call Free valve and it is a marvel. It not only allows control of the profile, overall, but a on a cylinder by cylinder valve by valve basis.
Similar thing with Mercedes' turbo charger. It is split, and it is impressive, but the benefits are more complex simply gaining from placing the compressor and turbine at different ends of the engine (e.g., moving intake charge away from exhaust heat, providing space for an ultra highspeed motor/generator on the turbo shaft) etc.
At the risk of sharing clickbait...there is an argument that current F1 cars are more energy efficient than a tesla (http://www.espn.co.uk/f1/story/_/id/15152695/f1-cars-more-ef...)
It does sound like click-bait, but I see the point they're making there. No one is proposing we all drive F1s, but for that performance regime, under those conditions, F1 is more efficient with it's energy usage in achieving a target output than a Tesla would be. I'm sure that decreases dramatically driving at pedestrian speeds.
It reminds me a bit of when I first read about the SR-71's J58 engine. I'm trying to remember where I saw it (I think it was in the book "Skunk Works") in that the SR-71 was actually most efficient running at Mach 3.2 than it was running at lower speeds. Seems counter-intuitive, but like F1, that was the situation for which it was designed.
http://raconteur.net/infographics/the-economics-of-formula-1
https://en.wikipedia.org/wiki/Redline#Examples_of_motorcycle...
Kawasaki ZXR 250: 19,000 rpm Honda CBR250RR: 19,000 rpm Yamaha FZR250: 18,500 rpm Yamaha YZF-R6: 16,200 rpm
Heck, remote control car nitromethane engines have operated in the 35000rpm - 40000 rpm range decades ago. But with minuscule displacements (~3cc).
If valve springs worked at those speeds and 2000+ cc displacements, trust me, Formula 1 wouldn't have abandoned them several decades ago.
Supercar manufacturer Koenigsegg is in the process of licensing their consumer version of the technology under the trade name "Freevalve". They've been developing it and testing it for an incredibly long time (I believe it's in its fourth or fifth generation), presumably to keep driving the costs down. I believe a few Chinese manufacturers are some of the initial companies signing on. It's around a 3-4% efficiency gain on its own.
There's other fun stuff too, like Mercedes-Benz's split turbochargers. Basically, the turbine is located near the exhaust still, but a shaft runs through the engine to the other side to the compressor which is near the intakes -- less piping to get a cooled charge, less turbo lag (again, shorter piping), a more compact engine footprint, and needing smaller intake side pods than using normal turbochargers. Be interesting to see if those trickle down to consumer autos, whereas currently manufacturers are instead integrating 48V electrical systems for electric turbochargers (and more advanced lighting, hybrid functionality, etc.)