None of them work properly. None of them has everyone on it. None of them add any value to communication. All of them throw ten minutes to the wind finding everyone to start with. I've missed 20 minutes of many meetings dealing with audio problems, network problems and firewall problems when we could have used a simple dial in conference system that has been around for over 10 years.
And I'm treated like a Luddite because you have to call me, SMS me or email me?!?
I don't want this any more. After a rant yesterday about WiFi and how it sucks and I've switched back to wired ethernet. I have to suggest that there was a technological singularity around 2005 which was 'peak utility' before the proliferation of sharecropped communications, technology with false utility, high cost and pay-per-everything.
To add other things to this problem set is going to cost me more money and time of which both are finite and at least one runs out uncontrollably.
Also, IPv6 FTW!
Yes IPv6 definitely FTW. We just migrated our office and two data centres to it. Life is good now. V6 firewalls are just packet filters; all our nets are in the public address space.
It seems that you either end up with devices having two addresses, and have to deal with all the broken software that assumes a machine only ever has one address, or you use a ULA and NAT which is no better than IPv4 in many ways.
There is a router that has an ethernet port on it. That's our internet in. Anything in front of that is ours. Anything behind we don't care about but there is a 100mbit local shared ethernet and a backup FTTP line. I assume it's switched to the same network at the peer end as if either goes down, we only have one address space. We have a couple of front-facing v4 addresses that handles incoming mail.
This all sits in a cabinet we don't touch owned by the provider.
The stupid thing is the LSE and fibre cables leave the building in the same pipe. Wonder how long it'll be before someone digs through it.
Just in case you want some nets to not be globally routeable, you guys are aware of the Unique Local Addressing block?
But never use non-globally-unique addresses as other commentators suggest with wonky probabilistic allocations. There is absolutely zero benefits for that, and it will inevitably end up to be a huge PITA down the line. IPv6 used to have 6-to-6 NAT and site-local addresses, but sanity won, and both were dropped from the current slew of RFCs.
Or, you can use RFC4193 (AKA ULA) space, which allocates a /48 and is designed to be non-routable, unless an admin chooses to make it routable.
RFC4193 specifies a prefix generation method and lays out the probability of collision. If you join two networks together, you've a (1.81x10^-10)% chance of prefix collision. If you join ten-thousand networks together, you have a 0.0045% chance of collision. [0] If my math is right [1], this means that you'd need to join 2,500,000 networks [2] together to have a 1% chance of a prefix collision.
I am squarely in the "If there's a chance that it can happen, it will happen." camp. However, I'm rather okay with those odds.
[0] Either my figures are right here, or you need to take those percentages and divide them by 1000 to arrive at the correct figure.
[1] And it may not be right!
[2] Networks -each with its own /48- as opposed to hosts.
But bigger point here is that often you will need external connectivity for those ULAs, similar to what everybody used to do in IPv4 world (i.e. NAPT, a.k.a. "nat overload" a.k.a. "IP masquerade"), and that is not something that is available, really. Instead, IPv6 offers prefix translation (a.k.a NPTv6, see RFC6296). So effectively that means that:
- for each LAN segment (i.e. /64) you have to have a "private /64" and a "public /64" (or same at coarser granularity up to /49 or even more). Twice the number of networks to configure and keep track of;
- "NAT as a security measure" argument flies out of the window, as NPTv6 is stateless.
In other words, you get all the hassle of IPv4 NAPT with none of its (meagre) benefits.
The whole point of using ULA space is for giving IP addresses to machines that you don't expect to need to contact machines in the globally-routable IP ranges. [0]
From the RFC:
This document defines an IPv6 unicast address format that is globally
unique and is intended for local communications, usually inside of a
site. These addresses are not expected to be routable on the global
Internet.
If it turns out that some of those machines actually need access to globally-routable space, then advertise a globally routable prefix to those machines and either keep advertising the ULA prefix, or -yanno-, don't. :)Fixing this particular network planning error shouldn't be much harder than unsetting some firewall and/or routing rules that break Internet access for machines that have been assigned a globally-routable address. :)
[0] On my LAN, I advertise a ULA prefix, as well as a globally-routable prefix. Because my globally-routable prefix is not static, [1] I use the ULA prefix as an ersatz poor-man's Provider-Independent allocation. This setup would be probably be somewhere between unreasonable and silly at a site that does have a static prefix assignment.
[1] Well, it's effectively static, but I don't have an SLA, so... ;)
I'm not sure how much experience you have with screwing around with router settings, your level of familiarity with IP networking concepts, or even what software you're using on your router, so I'll give some background information on prefix advertisement, and describe prefix generation and how you might actually advertise a ULA prefix on a router running OpenWRT. Because the underlying software that does the work should be the same regardless of router model, reading about how it is done on OpenWRT might give you a starting point to discover how it's done -if it is at all- on your router model. I'm more than happy to clarify anything that's confusing, give additional information, or track down and read documentation for a particular router!
Background information:
Many routers use a piece of software called radvd to advertise IPv6 routes. Radvd -effectively- takes a list of network interfaces, each with a list of router advertisment options, and transmits advertisements on those interfaces. radvd has a config file whose syntax is documented here [0]. A minimal radvd config file would look like
interface eth0
{
AdvSendAdvert on;
prefix ::/64
{
AdvOnLink on;
AdvAutonomous on;
};
};
This would instruct radvd to advertise whatever prefix had been assigned to the interface named eth0 to machines attached to eth0. Note that an interface section can have multiple prefix sections. If you have a particular prefix that you want to advertise, replace "::/64" with that prefix. The overwhelming majority of options in the radvd config file are both entirely optional, and entirely unneeded in most situations.Now, I suspect that on most routers that support prefix advertisement, you'll never need to touch an radvd config file. Like I said, this is just background information. So, let's get to generating your ULA prefix:
Generating your ULA prefix:
Get the MAC address of a computer that you control.
Go to https://www.sixxs.net/tools/grh/ula/ and plug that MAC address into the MAC address field on the page. You'll get a value back that of the form: fdaa:aaaa:aaaa::/48 This is your ULA prefix.
Advertising a /48 is kind of awkward for downstream devices. You need to carve out a /64. So, take that ULA prefix, add a colon and four zeroes to it and replace the /48 with a /64 like so: fdaa:aaaa:aaaa:0000::/64 You can now go to advertise this on your LAN. [1]
Advertising the prefix:
I actually have no idea what the prefix advertisement option is called on most consumer routers, or if it even exists on your router. A quick look at Belkin's and Linksys's support sites didn't turn up anything promising. I would dig around in the IPv6 settings tabs until I found something that looked promising, or had exhausted all options. [2]
If you're using a recent version of OpenWRT (That is, OpenWRT Barrier Breaker or later), /etc/config/network has a ula_prefix option in the globals section that's used for exactly this. [3][4]
If you're using a version of OpenWRT earlier than Barrier Breaker, you can tell radvd to advertise your ULA on your LAN interfaces. The prefix section of /etc/config/radvd is used for this. /etc/config/radvd is documented here [6]. You can have multiple prefix sections for each LAN interface. [7]
Now, reload the network config (Call /etc/init.d/network with either the reload or restart option, I can't remember which.), wait for a minute or two, and machines on your LAN should have a new IPv6 address in the /64 that we carved out of the ULA.
If everything's working, -optionally- register your newly-generated prefix with SixXS at the page where you generated your ULA prefix.
Feel free to ask any questions that you have. :D
[0] http://linux.die.net/man/5/radvd.conf
[1] Note that you can create 16 bits worth of networks out of your /48, not just one network.
[2] If you can tell me the make and model of your router, I'd be happy to try to find and read the documentation for it. :)
[3] http://wiki.openwrt.org/doc/uci/network
[4] Though, to be frank, I can't remember if you plug in the /48 and it automatically creates /64s for each LAN interface that you have configured [5], or if you can only plug a single /64 into it. I would try the /48 first.
[5] OpenWRT lets you set up multiple LAN interfaces. I found this useful when I was using VLANs to make isolated WiFi guest networks.
[6] http://wiki.openwrt.org/doc/uci/radvd
[7] So, if you have IPv6 service from your ISP, you can advertise the ISP-provided prefix and your ULA prefix. Have one prefix section that contains no prefix option, and a second prefix section that contains a prefix option whose value is the /64 that you created earlier.
Edit: Also, you might be interested in reading about the NETMAP iptables/ip6tables target. See iptables-extensions(8) for more info.
[0] https://tools.ietf.org/html/rfc4193#section-3.2
It's been quite some time, and the details are hazy, but I remember the process of getting a tunnelbroker.net tunnel configured, and the subsequent (totally optional) series of knowledge tests required to unblock IRC over the tunnel taught me a fair bit about IPv6 and some about (reverse DNS? forward DNS?) glue records.
Figuring out the meaning of all of the options available in an radvd config file was also rather educational. (20->40% of the educational value was in reading about things that were tangentially related to whatever the radvd configuration item was.)
I'm having difficulty parsing your second sentence. So, I'll say this: If you're a tech business and can't manage to cost-effectively manage the settings on your border equipment, you're doing something really wrong. :)
MSP=Managed Service Provider. Basically rip off merchants who charge you for everything because you are trying to run a business with the tech rather than run an operations team.
http://www.preservenet.com/theory/Illich/IllichTools.html
"Watershed (figurative definition, as used by Illich): A point in the historical process when a particular “tool” creates a quantum shift in society, like the sudden application of gravity feeding water into a terrain basin (literal watershed)."[0]
[0] http://www.democraticunderground.com/discuss/duboard.php?az=...
In particular, I've found a 10Mb LAN outperforms a 1000Mb WiFi for networked filesystem access.
I would suggest getting a better router, and making sure other factors are set correctly to maximise signal strength rather than blaming WIFI. Location of the router, whether you use a range extender and so on.
I don't stream any media, just do file copies. It sucks whatever I try.
In my experience, SMS and Hangouts are equally unreliable messaging protocols. Messages sent through either transport can be delayed for arbitrary lengths of time or lost entirely.
Everything that's happened with Hangouts that's unrelated to video calling just makes me so sad.
Not for IM nor for SMS. After that Google Talk (and thus XMPP) was dead to me.
For SMS I could at least revert to the stock AOSP messaging app.
Any client that speaks XMPP should work just fine to reach into Google's IM silo for direct messaging. I make frequent, daily use of Pidgin for this purpose. Sadly, the only way to access group chats is through the official client.
Also: If you haven't already, check out TextSecure by Open Whisper Systems. It has the best group-SMS handling of any MMS client I've tried. It's also made and maintained by a group of folks who are really concerned with making secure software that also happens to be as easy to use as is possible.
Yes, I may not have push via the cloud to my latest iGizmo, but at least I don't have to worry that I forgot an important calendar, todo, file, or chat message on one of 5 services that mix and match between what they offer.
Org-mode can run calendar, todo, notes, habits, journal, etc.
Chat is where I still haven't found a solution. Switching to XMPP/SMS semi-exclusively is probably the next step.
Before my iGizmo I carried around a notebook, but that was larger, more cumbersome and had less flexibility (I can add a grocery list item from my PC in the kitchen or even input it by voice if I realize I need something).
That means that for some of us, a better solution rather than a simpler one is what we desperately hope for.
I have node-red generating dynamic HTML, and dumping it in var/www/html and apache serving it up. All I'm waiting for now is 30 more setups for testing purposes.
(nRF24L01+ can generate a self-healing mesh network. Given the weird shape of our building, makes this ideal. And a small change turns a sensor node into a sensor/gateway.)
We had a standard for chat, it's called XMPP, and before that we had IRC. I know they're all non-optimal for mobile use but some goddamn standards (tm) would make my life easier.
I can't believe we were better off in the heydays of Trillian - at least all my contact lists were in one program!
Maybe I should go back to SMS.
Now, on home automation. I came to some of the same conclusions as the author - we're screwed when it comes to being at the behest of big companies and proprietary protocols to control devices we should own.
I just dread having to write yet another home automation framework when I do finally automate my doors, windows and lights. Now where did I put my keys again?