While they might seem to be arbitrary, they are obviously not the least bit arbitrary.
The base size A0 has an area of exactly 1 square meter. Each subsequent size is constructed by taking half of the previous, so for A4 it's 1/16th of a square meter, or 0.0625 sqare meters, 625 square centimeters, which is 21.0 cm x 27.9 cm (approximately).
In order to have both the halving property and the self-similarity the aspect ratio has to be sqrt(2), and therefore you can't have nice little round numbers for the sides.
If I have to choose between self-similarity and nice round numbers, I'll take self-similarity, thank you.
Which is still arbitrary :)
However, there are some good ways to use 8.5 x 11 [2] that might look odd on narrower and taller paper.
[1] http://marginalrevolution.com/marginalrevolution/2012/09/why...
[2] http://retinart.net/graphic-design/secret-law-of-page-harmon...
In relatively big jumps (of the same proportion), though. Not enough in-between sizes (of the same proportion).
Yes, additional sizes address the desire for satisfying the missing in-between sizes.
No, because I'd like to keep it simple and avoid having to do that or even think about it at all.
Basically, with the ANSI sizes you want to satisfy TWO proportions with gradual size changes instead of just ONE proportion with gradual size changes as seen in ISO 216. This is where the discussion cycles back to the utility of 1:√2.
In most offices in the U.S. that I've been in (I say this in a fast and loose fashion), they carry three sizes (with the following typical uses):
(1) ANSI A (US Letter) for standard letters (uses full portrait page) and leaflets (uses one-third landscape page) or booklets (uses half landscape page).
(2) US Legal because there are plenty of legal documents are out there that use US Legal (uses full portrait page). And perhaps as a bonus, but not as frequently seen, US Legal can be folded into small booklets (uses half landscape page). Although, I don't see this happen as much as ANSI A being used for booklets.
(3) ANSI B (Ledger/Tabloid) because it can be great for spreadsheets and folded to US Letter sized pages. Either for collapsing the spreadsheet or for making booklets with US Letter sized pages (uses half landscape page).
Now, yes, I did not mention all uses. I merely mentioned what I have frequently seen used based on my experience. But one of the key take-away points for the "common-use/general-purpose" ANSI A and ANSI B paper sheets is the notion of folding the paper in half to form a booklet.
You don't see many offices carrying ANSI C (17"x22"), which is the next step up from ANSI A maintaining the same proportion. (So availability of this is considered unlikely in this context.)
Of the three, perhaps US Legal can stand alone because it offers a significantly relevant special situation proportion. So, we'll set US Legal aside for now.
And so, you get usage of Half US Letter (1.5454…), Full US Letter (1.2941…), Half Tabloid (which is just US Letter, 1.2941…), Full Tabloid (1.5454…). So, you'll get an oscillation of two distinct proportions with paper that doesn't use 1:√2, and in the case of ANSI A through ANSI E, you get the 1.5454… and 1.2941… oscillation.
Now, if you had ISO 216 sized paper, all of the proportions would be the same no matter what, and it becomes very easy to choose between paper and half-paper sizes because they all work alike with regard to their proportions.
However, with the oscillating ratios, you have to choose which one you're targeting and be sure of it, because the next larger (or next smaller) size is significantly different.
Now, more in-between sizes could solve this, but that also means you'd probably end up carrying around yet another paper size because of it. If you simplify things by getting rid of the dual-proportions and have a unified proportion instead, then the added frustration from the differing layout proportions go away instead of trying to address that with another paper size for something in-between.
So, to parallel the Half US Letter (feels like an oddball that is basically super small Tabloid, 1.5454…), Full US Letter (1.2941…), Half Tabloid (is just Letter, 1.2941…), Full Tabloid (1.5454…):
Half A4 (is just A5, 1.4142…), Full A4 (1.4142…), Half A3 (is just A4, 1.4142…), and Full A3 (1.4142…).
With the layout for Half US Letter, your next proportional step-up is Full Tabloid. (Huge jump!) Or from Tabloid, your next proportional step-down is Half US Letter (Really small!) You could have an in-between size to satisfy it, but it seems excessive when you could have just had used the 1:√2 proportion to begin with and not worry about any of those additional considerations.
---------------------------------------------------------
Saying it another way...
Where, ½·x signifies folding a sheet for purpose as a booklet, and the paper that satisfies that requirement is mentioned inside the cell.
Dealing with only our "letter" size (1) and "tabloid" size (2) sheets that we have in our office, we get the following:
ANSI | ½·1 | 1·1 | ½·2 | 1·2 |
+—————+—————+—————+—————+
1.2941… | :( | A | B | :( |
|—————|—————|—————|—————|
1.5454… | A | :( | :( | B |
|_____|_____|_____|_____|
ISO 216 | ½·1 | 1·1 | ½·2 | 1·2 |
+—————+—————+—————+—————+
1.4142… | A4 | A4 | A3 | A3 |
|_____|_____|_____|_____|
With ANSI: We don’t have a “half size” booklet with 1.2941… proportions.
We don’t have a “full size” sheet with 1.5454… proportions.
We don’t have a “full size” booklet with 1.5454… proportions.
We don’t have a “double size” sheet with 1.2941… proportions.
With ISO 216: We have our “half size” booklet in all our proportions.
We have our “full size” sheet in all our proportions.
We have our “full size” booklet in all our proportions.
We have our “double size” sheet in all our proportions.
(Because we only have one proportion to deal with,
there’s no bothering to deal with dual proportions.)
That's four frowning faces (missing solutions for that proportion) on the ANSI side.---------------------------------------------------------
If we were to expand on this beyond the "two typical sizes found in the office" scenario, we get the following:
ANSI | ½·1 | 1·1 | ½·2 | 1·2 | ½·4 | 1·4 | ½·8 | 1·8 | ½·16 | 1·16 |
+—————+—————+—————+—————+—————+—————+—————+—————+——————+——————|
1.2941… | :( | A | B | :( | :( | C | D | :( | :( | E |
|—————|—————|—————|—————|—————|—————|—————|—————+——————+——————|
1.5454… | A | :( | :( | B | C | :( | :( | D | E | :( |
|_____|_____|_____|_____|_____|_____|_____|_____|______|______|
ISO 216 | ½·1 | 1·1 | ½·2 | 1·2 | ½·4 | 1·4 | ½·8 | 1·8 | ½·16 | 1·16 |
+—————+—————+—————+—————+—————+—————+—————+—————+——————+——————|
1.4142… | A4 | A4 | A3 | A3 | A2 | A2 | A1 | A1 | A0 | A0 |
|_____|_____|_____|_____|_____|_____|_____|_____|______|______|
That's 10 frowning faces on the ANSI side, and no frowns on the ISO side. The ISO side inherently avoids the frowning face scenario.Yes, you could add on another set of sizes to address the missing proportions on the ANSI side. But, that's inelegant and unnecessary if you just went with the ISO way instead.
Standard printer paper is 80g/m2: A1 = 40g, A2 = 20g, A3=10g and A4=5g.
Or, alternatively, crumple up A4 sheets for quick 5g weights.
The issues that come up with regard to US Letter size paper seem to be:
1) It's not metric -- yes that's true, but A4 is 210mm x 297mm. These numbers seem completely arbitrary and don't take advantage of the metric system. I wish the US was on the metric system, but it's not so 8.5 in by 11 inches at least has the advantage that it is measured in simple numbers with respect to standard measures in the US.
2) It's easier to store and work with A4 because it is one half of an A3 sheet -- however, US Letter is one half of the US Tabloid/Ledger size. The ANSI (American National Standards Institute) paper sizes in inches are A (8.5 x 11), B (11 x 17), C (17 x 22), D (22 x 34), etc. and share this advantage with the ISO standard.
3) The aspect ratio is is approximately sqrt(2)/2 for all paper in the A series, the B series, and the C series. But why is having but one shape of paper an advantage? Sometimes it's useful to have choices depending on the content to be printed on the paper. Furthermore, the ANSI paper sizes simply have two aspect ratios alternating as one increases paper size.
It is argued that printing posters with corresponding flyers is easier with ISO paper sizes. But this is true with ANSI paper sizes: one would have to jump up two sizes from letter (ANSI A, 8.5 x 11 inches) to ANSI C (17 x 22 inches). So, for the case where one would like to print at ANSI B, the aspect ratio of the page is a bit different. Here we have, what appears to me, to be the first real advantage of ISO over ANSI paper, where we need to print a flyer at A4 and A5 (but not A6). However, this hasn't been a problem for me personally. I'm usually working with pages that have additional constraints. For example space for bindings or differences in margins between recto and verso sides of two sided printing. Whenever there are bindings involved the aspect ratio advantage goes out the window.
4) Every country uses ISO sizes, why not the US (and Canada and Mexico) -- well, this is oversimplifying things a bit. Take a look at the Wikipedia page for paper sizes. There are Japanese variants, German extensions, and Swedish extensions listed that deviate from the ISO standards. There are also Architectural sizes listed that are designed to have simple ratios for their aspect ratios.
The idea that we would somehow be better off with fewer choices (just one) really for aspect ratio really strikes me as wrong. I like all the variety available in paper.