I really don't think that will happen. The reason your new cast iron pan doesn't have that shine is because they've changed how they make them.
A few things I do:
Use wire mesh to clean, quickly, immediately after cooking.
Only use tap water to clean it. No detergents. This allows the pan to develop a literal taste of its own after a few months or years.
Heat the pan after cleaning, evaporating all water.
For stuck-on food, I've had best luck with a coarse copper mesh pad (e.g. Chore Boy), which I use lightly, and only to remove the gunk.
In the past, I'd also used coarse salt as an abrasive, but I like the copper wool better.
I also heat the pan to dry it off. As to the comment about this promoting rust: if you have a well-seasoned pan, you don't have any wet metal; you have a wet seasoned pan. You could just as easily dry it with a dish towel, but this tends to get your dish towel dirty.
Don't do that. It causes rust.
Metal rusts MUCH faster when hot than when cold. If you have wet metal that you are worried will rust get it as cold as possible, and let it dry. Best place is in the fridge - it's cold, plus low humidity helps.
A fridge is not necessary for cast iron, but don't heat it when wet.
The point is don't warm it to dry thinking it will rust less since it's wet for less time. Just let it dry in regular air.
If it dries say 50 times faster, does iron rust more than 50 times faster at 400F than at 70?
I have no way of knowing either way, but I've got a cast iron pan that belonged to my great grandmother and I remember my grandmother heating it to dry it off. My mom did the same with it, and now I've done the same--no rust.
I took two identical pieces of metal. Dried one in a warm stove the other on a table.
The one on a table had no visible rust. The one in a stove was completely orange.
There's a pretty big difference between drying something in a warm stove vs applying a direct flame to it on the stove top.
It takes just a few minutes to get the skillet hot enough where the water pretty much instantly evaporates. I'd imagine putting it in a warm stove took much longer to completely dry it.
Reaction speed doubles for every 10 degrees F, but evaporation doesn't.
That can't possibly be correct, or at least it's only correct over part of the range.
If a pan rusts at a given rate at 70F, it would rust at 2^33 times that at 400F--those numbers just don't work at all.
Also once the pan heats past the boiling point of water, there is a huge decrease in drying time.
What I said was that if you are heating the iron in order to speed up evaporation to avoid rust, you are being counter productive. You will avoid more rust (if any would be formed in the fist place), by just letting it air dry.
But it's certainly not helping.
The methodology was not complicated: I washed some porous/rough metal under the faucet, dried it with a paper towel, then put one piece in the oven at 170F, one on the table.
300-400 (what you'd get from the stove top) is above the boiling point, so the water rapidly boils off.
These 2 things aren't comparable.
Here's a counter example: There are many tons of metal in hot desert climates that have a small amount of rust on them, but nothing like the kind of rust from a cold wet climate. There may be complications from cooking, but, and this is without giving it much thought, I'd say that water is a much larger factor than heat.
You still need water.
1. Get the oil hot before you add any foods.
2. Use a sheet-metal spatula/flipper
Humanity has known for a long time that when you get your cooking oil hot, it repels food instead of binding it to the cooking surface; but the amateur cook has forgotten because of a reliance on non-stick surfaces.
The sheet-metal spatula/flipper lets you clean the cast iron with each pass of the tool. A rubber/wooden tool will leave small, burnt on bits of food, which accumulate more bits of food; a sheet-metal tool with scrape those off before they become a problem. Also, a sheet-metal spatula will scrape the roughness of the cast-iron from the bottom of your pan over the course of decades, moving you towards that inky-black mirror of grandma's old pans.
I can cook anything on my cast iron, just by following those steps, even fried eggs: the surface is totally non-stick. And cleaning is simple too: sometimes I'll make a few passes with the spatula to scrape off any food that has dried on, but that's all I ever do.