News for hackers. Stuff that matters.
Re:Putting $10M into UBeam illustrates what is wrong with te... by Animats on Saturday November 01, 2014 @02:52AM (#8542381)
I've been looking closely at the UBeam demo video at

  http://on.aol.com/video/ubeam-wireless-power-demonstration-at-d9-517342543
There's a lot of information one can get from that video if you turn the resolution up to 720p and look at still frames.

The meter is reading voltage, on what appears to be the 10 VAC scale. (Someone wrote it was on ohms, but it's not.) About 4V is coming out. We don't know what, if anything is the load, and there's no current measurement, so we can't compute power. It's interesting that they're measuring AC voltage while supposedly charging a DC device, a phone.

The ultrasonic transducers seem to be common hobbyist-level range sensors as used on small robots. Like these:

https://www.futurlec.com/Ultrasonic_Sensors.shtml

At 00:31 into the video, there's a good view of the back of the board holding the ultrasonic receivers. If you take a screenshot of this and enhance it, you can see the wiring. There are just two wires coming out of the receiver, and it looks like all the sensors are just wired in series. That maximizes voltage at the expense of current, of course.

The transmit array has 10 transducers in a hexagonal pattern, which helps focus the beam. (That transducer is a rather broad-beamed device.) The transmit end is powered by a hefty looking power supply, so those transducers are probably being driven hard.

With that setup, they should be able to get a few volts out of the receiver end, using the same kind of off the shelf transducer at both ends. This is something you could put together in a day or so after ordering the parts. There doesn't seem to be anything new here at all in the demo version.

The efficiency is probably a few percent. That's for this ideal case - transmitter pointed directly at receiver. The Wireless Power Consortium inductive wireless charging people report 60% efficiency, and they're trying to get to 80%.

The patent application talks about steering and focusing the beam, but you're still going to need line of sight, and a big emitter array.

Re:Putting $10M into UBeam illustrates what is wrong with te... by KaiserPro on Saturday November 01, 2014 @03:21AM (#8542416)
You might be able to beam form a bit more efficiency, however one thing you can't escape is the angle at which the receiver is pointing.

All microphones have polar patterns. There are areas that are more sensistive, areas that are less.

So not only does it need line of sight, it'll need to be pointing at transmitter.

It's also interesting to note that we've had wireless charging for at least 5 years, but none of them yet are long distance. they are all mats that you put the device on.

Re:Putting $10M into UBeam illustrates what is wrong with te... by kybernetyk on Saturday November 01, 2014 @09:28AM (#8542953)
> but none of them yet are long distance.

Possibly because of the pesky inverse square law. A mat is "good enough" and trying to achieve remote wireless charging would probably induce exponential engineering head aches for not much gain.

Re:Putting $10M into UBeam illustrates what is wrong with te... by KaiserPro on Saturday November 01, 2014 @04:09PM (#8544420)
Physics. Its a bastard.
Re:Putting $10M into UBeam illustrates what is wrong with te... by raverbashing on Saturday November 01, 2014 @05:17AM (#8542558)
> It's interesting that they're measuring AC voltage while supposedly charging a DC device, a phone.

No, it's not weird. DC would come later.

Re:Putting $10M into UBeam illustrates what is wrong with te... by lemonberry on Saturday November 01, 2014 @08:27AM (#8542827)
interesting != weird
Re:Putting $10M into UBeam illustrates what is wrong with te... by nitro20045 on Saturday November 01, 2014 @05:21PM (#8544669)
Yeah, I examined the video, too, with the same conclusion. It's comical that no one thought to measure the current, too, before dropping $10M on them.