I ended up not doing this because the Seebeck effect isn't really a useful power-plant (in the broad sense of the word) when you have a small temperature gradient because it is really inefficient, although it is useful for thermometers and other low power items, and for some exotic things like Radioisotope Thermoelectric Generators, which is what powers Voyager and other long distance spacecraft. It becomes worth using when you have a large, consistent energy source, which is usually geothermal energy. But the small temperature difference between the human body and the flashlight and the low efficiency of thermocouples means that this project won't seriously compete with battery powered flashlights. However, it is a cool idea and could have some niche uses.
Good on your for using peltiers back in HS. In HS I made a sweet exoskeleton using peltiers for active cooling while outside in the summer heat.
Yep, I was going to try to use that (peltier) in conjunction with a small array of solar panels to cool my car because summer afternoons can get incredibly hot - outside temperature reaches 45C, so I'm reasonably sure the car's interior would reach 55-60 easy. Alas! running some back of the envelope calculations (before jumping into the whole thing) I quickly discovered that I'm better off trying to find an efficient and tiny compressor, and large secondary battery to charge off the solar panels.
This problem still remains unsolved and no, remote start is not an option. I'm trying to craft something that is completely independent of the gas in the tank and preferably self sufficient.
A simple reflective car cover would do far more than all of that tech.
Smetimes it is really easy to over-engineer solutions to problems. I am reminded (and I am guilty) of this frequently.
I do realize that the problem needs to be approached two fold - expelling hot air outside to reach ambient + cooling air that's being taken in some manner.
So, if your willing to go all out and spend a few thousand on modding your car. Automatic shades for every window, a fair sized solar array on the roof and an independent AC system designed for continuous operation.
Speaking of phase-change materials, why not fill the flashlight with them? It still wouldn't be steady-state of course, but I envision the fan eating up all the power. Heat pipes might help, but they still leave the problem of heat rejection. Evaporative cooling pad?
Idea: using PCM you could make a flashlight that you recharge in the oven.
Combining ideas may make sense here. A flashlight with PCM and a black handle that you can leave in the sun, and optionally wrap in a soaked cloth. Perhaps PV makes more sense, but I haven't run the math.
Of course, you'd also want a thermos to carry it in. ;)
http://en.wikipedia.org/wiki/Lunar_Roving_Vehicle#Wheels_and...
Basically, the heat was stored in the wax, which melted. Then, radiators would pull the heat from the wax out into space when the Rover was resting, which would solidify the wax again ready for the next run.
Think of sink/source temperature, cost/mass/performance/reliability tradeoffs, air vs. vacuum, power requirements, etc.
What about a series of smaller copper tubes that then stick out the bottom of the handle to transfer heat from inside to outer air?
http://boingboing.net/2011/10/26/coffee-joulies-review-the-e...
I guess it also depends on the relative importance of mass vs. volume optimization.
Maybe there's some way to lower the melting point of paraffin?
Evaporative cooling could work, but if you are planning on even including 20ml of cooling liquid, you could just as well put a CR2032 battery in there, which'll power the thing just fine.
Also note, calling the device a Peltier is a misnomer, her flashlight is a thermoelectric device utilizing the Seebeck Effect, similar but opposite to the Peltier Effect. Peltier has just become the connotation for thermoelectric devices.
The Seebeck effect only works with a temperature gradient, the flashlight will begin to heat up when held and the Peltier will produce less power. The next step is to add a heat sink and fan to maintain a temperature gradient for operation longer than 20mins.