It's because of how load cells (and scales) are manufactured. They're made for weight classes like 100g, 1kg, 2kg, 3kg, 5kg, 10kg, etc. So to make a scale for a particular weight you pick the load cells you'll need for the range you want.
Higher quality scales don't select higher quality load cells; they're all the same (reasonable quality) for the most part! Instead they just use more load cells and just take an average of all their values, multiplied by the number of cells, to measure weight.
So if you want a damned accurate industrial scale for measuring weights around 1kg you'd use like twelve 100g load cells rather than a single 2kg load cell or two 1kg load cells. Of course, then the hard part becomes, "how do I distribute this weight perfectly evenly across all of them?" so you have to take tolerances into account to make sure that at no point can weighing part of your scale rub against the side of its container or accidentally get something wedged between the scale part and the case.
There's loads of other things to consider as well but for the most part the accuracy of the scale is a factor of how many load cells its using, not the quality/manufacturing tolerances of the load cells themselves. Because even with the most precise manufacturing methods load cells will still drift and be impacted by temperature. All you can do is calibrate regularly, test them, and hope for the best (or use a completely different technology).
They want the highest resolution so they can see their 10 gram progress when dieting. But they want the measurement to be stable enough to not cause them too much anxiety.
Do they? 100g is already quite granular, and you can lose that in a day.
I have two scales which are giving me different measures - I've been weighting myself and assume I'm in the middle of both. It's a bit annoying, but works for my goals.
Yet somehow they got along just fine with analog scales. No, everyone knows that scales lie, and to anyone with mechanical engineering intuition it's plain as day why they lie: because they can cover up the cheapness and inadequacy of their flextures that way.
The other one, weight, is easy enough and if it's not accurate it is for commercial reasons. Either because what I said or what you said. Both could be true.
Even the cheapest load cell is pretty damned accurate and the average between the four of them is going to be accurate within 0.1kg (~0.22lbs). Having said that, load cells have this problem where their values drift over time but only if there's a constant weight on them. If you step off the scale and allow it to re-calibrate itself (which is what it does every time it turns on) there will definitely not be enough drift to matter from a, "how much do I weigh?" standpoint. All it takes is like 2 seconds without weight for a load cell to "settle down" back to its not-actually-very-noisy resting position.
I've tested loads of the cheapest possible load cells money could buy along with some load cells I took from an expensive transparent scale that had cracked. They were all far more accurate than I was expecting and any differences between them was negligible.
The longer you wait before weighing something the less accurate it'll be but only by tiny, negligible amounts. Like, if you're weighing something that's 100kg and you waited ten minutes after calibration (something most scales won't allow because they all have something like a 30-second timeout) you'd still get a value that's within 0.01 of 100kg. They don't drift that much at rest unless there's some serious temperature variations or you had something resting on the scale the entire time.
Is it a big problem? No, but there's a fake decimal and an attempt to hide that the decimal is fake. Not cool.
I've never seen a human weight scale that went beyond a single decimal place and in all honestly they're going to be very accurate. If you get on the scale and it says 201.2lbs that measurement is going to be accurate within ±0.1lbs (actually, more than that but you only get one decimal point of precision). If you put the scale next to something that's emitting a ton of electrical noise then maybe it'll be off by 0.2lbs but I doubt it.
My cat sat on it, read 9.4lb. I stood on it, it gave my weight, then I picked up my cat and it read (my weight + 9.4)lb.
I was impressed!
Low cost air quality measurement is difficult. PM is tricky but almost manageable with laser scattering, toxic gases are almost impossible to get right with electrochemical sensors, no matter how much money you throw at them.
Weight measurement is easy, they could give you precise and accurate results but most customer base doesn't understand anything of physical quantities measurement and would panic they gained 50g in a minute if they showed up the real fluctuating values by stepping on the scale twice.