Approximately 10 percent of the U.S. adult population — over 25 million Americans — experience some form of tinnitus. And an even larger percentage is suffering from hearing impairments.
Broken mufflers and loud engines mask the tinnitus sounds and finally they can relax. This is also the reason why they prefer to hang their Freeways in the air, in the middle of the city. And why their cafes are unbearably loud with the sound of refrigerators competing with the loud music.
There are some people who prefer to have fun in other ways. Like having a conversation outdoors in a cafe, uninterrupted by a loud car parking right next and spitting out the exhaust right onto the table. Or enjoying sound of the people around and children playing. But not Americans. They only like their cars, the roads and the vast expanses of the parking lots.
But you have to realize America is enormous--its over 2600 miles to drive end to end. Our highway system and infrastructure isn't setup to completely replace gas or diesel with electric for long term trips. It's getting much better, but I suspect reluctance to get an electric car in the US primarily comes down to cost and range anxiety.
It additionally talks about the unusual pattern used in modern voodoo engines in the Ford Mustang (which is also mentioned in the article). The video is very similar to this article.
Re: Ford Mustang [1]
[1] https://www.pocket-lint.com/cars/news/ford/131151-ford-admit...
On the other hand, I also like the sound of two-stroke diesels.
The article also points out that GMs LT6 flat-plane V8 for the Corvette Z06 has a sound different from the F355, this apparently being deliberate design choice made by choosing which harmonics to emphasize in the exhaust system.
You say that flat-plane engines do not require the complex header primaries that have to cross over from one bank to the other, but AFAIK typical road car and truck V8s do not have such headers[1]. Would the purpose of such headers be to give a cross-plane V8 scavenging about as good as a flat-plane one, all else being equal? In that case, would the cross-plane engine lose most of its distinctive sound?
I would be interested in hearing the difference between otherwise comparable flat-plane and cross-plane V8s at the same RPM.
> You say that flat-plane engines do not require the complex header primaries that have to cross over from one bank to the other, but AFAIK typical road car and truck V8s do not have such headers[1]. Would the purpose of such headers be to give a cross-plane V8 scavenging about as good as a flat-plane one, all else being equal?
Yes, but as you point out deployments of this technique are limited due to packaging, cost, and even other performance parameters. See the GT40 “bundle of snake” headers for an example.
For a notable example of the other performance parameters, exhaust header lengths are tuned to the powerband of the engine such that shorter headers are more efficient at higher RPMs and longer headers at higher RPMs. This can even get into resonant effects as with intake runners. It’s difficult to design cross bank headers short enough to suit modern high-rpm engines, with the exception of the “hot-V”, exhaust inside intake outside, concept deployed on German V8s from BMW, Mercedes, and Porsche on the 918 (though the latter is a flatplane crank).
> In that case, would the cross-plane engine lose most of its distinctive sound?
Yes
crossplane: https://www.youtube.com/watch?v=vpswVBOC8lk
flatplane: https://www.youtube.com/watch?v=5r7X9L8_pS4
Most italian/european sports cars (with the exception of Mercedes in the past 3 years because American customers) have machined their crankshafts as "flatplane" cranks. Flat-plane cranks, no matter what firing order they have, will always alternate from bank to bank. This yields optimum exhaust scavenging and thus doesn't require the more complex header primaries that have to cross over from one bank to the other. Due to their design they don't need huge counterweights, which is why they rev up so quickly. The downside is that they suffer from secondary vibrations and have lower torque.
Americans typically machine closer to if not dead-on a crossplane crank or cruciform crank. the four crank pins are positioned in two planes, offset by 90 degrees. Typically the two outer pins are perpendicular to the outer and the two end pins are in one 180-degree plane. exhaust gas scavenging isn't as efficient as with a flat-plane crank, but that sound is worth it. This design necessitates larger counterweights to achieve a proper engine balance. The result is that you don't have the secondary vibration problems associated with flat-plane cranks. But they also don't rev as fast or as high. pick crossplane when you want torque imo.
I personally understand that a euro flat-plane crank is superior in its efficiency and power for racing, but the crossplane sound just melts my cold American heart when i hear it.