News for hackers. Stuff that matters.
Re:The Physics of baking good Pizza (2018) by SideburnsOfDoom on Wednesday December 21, 2022 @01:43PM (#34084605)
> My Ooni experience has been very bad

Sorry to hear that, but maybe you can still work at it.

> at the back it's 900, at the front 600. This is after an hour of warm-up.

I think that it will be as hot as it is going to get, after about 30 mins.

I get a touch over 500c at the back corner (maybe 950F) and a bit over 300C (600F) at the front lip. This should be right, with a centre at 350 to 400C

> rolling pin, or hand-stretch?

I hand-stretch, but also autolyse.

> lots of flour on the peel.

Semolina. Put your friend Semolina on the peel. It's a very coarse flour, as opposed to pizza flour, which is very fine. It makes the pie slide like it's little dry ball-bearings. Semolina.

If you can't get Semolina, use coarse cornmeal.

The next time you have pizza in a relatively authentic Italian place, run your finger along the underside of the pizza. You should feel a slightly rough, sandpapery texture that isn't present on top. That's from the semolina.

Just before launch, give the pizza a back-and-forth shake on the peel first, to be sure that it's moving, and get it moving if need be. You should know that it's not sticking to the peel, because you've seen/felt it move a bit.

Do you use the same peel to launch and to extract? Typically this is not recommended as the extraction can make that peel hot and moist, which would affect the next launch. Launch off wood or aluminium. Extract with aluminium or other metal peel.

Look for the "ultra-low zone" trick for turning the flame down very low after launch.

You will get these tips in https://www.reddit.com/r/ooni

You can see techniques demo'd on youtube. e.g. ulttra-low zone: https://www.youtube.com/watch?v=VAGmW4SI4PU and shake https://www.youtube.com/watch?v=VkD-IrTNpTk&t=27s Don't give up, there are tricks and techniques to learn.

Re:The Physics of baking good Pizza (2018) by peteradio on Wednesday December 21, 2022 @02:17PM (#34085076)
> Do you use the same peel to launch and to extract? Typically this is not recommended as the extraction can make that peel hot and moist, which would affect the next launch. Launch off wood or aluminium. Extract with aluminium or other metal peel.

Alternatively, scrub the peel with cornmeal between launch and next pizza.

Re:The Physics of baking good Pizza (2018) by SideburnsOfDoom on Wednesday December 21, 2022 @03:43PM (#34086138)
> Alternatively, scrub the peel with cornmeal between launch and next pizza

You would have to make do like that if you only have one peel, but in general you'll be better off with separate Launch, turning and extraction peels. They do different jobs and so have different designs.

The turning peel is typically quite different to the other two, but as mentioned, you'll do better with 2 different ones for launch and extraction. Wood is great for launch, terrible for extraction - you can't keep it in a hot oven for any length of time. And a metal peel that has warmed up during doming and extraction would be worse for the next launch.

Also, the launch peel can be prepped for the next launch by someone else, while the current pizza is cooking.

Re:The Physics of baking good Pizza (2018) by peteradio on Wednesday December 21, 2022 @05:37PM (#34087322)
Absolutely, I have a separate turner. All good points, but it can be done without. Generally my flow once things get going is:

1) clean launcher (scrub with cornmeal to remove sauce burned cheese etc) (15 seconds)

2) heavily flour the launcher with fresh cornmeal and kneed flat a single pizza dough (1 min)

3) build pizza with toppings (30 seconds)

4) launch, watch for flare ups (pull pizza away from flare ups and let burn out before pushing back forward), turn as cheese browns until all surface cooked (1-2 min)

5) take out pizza and set aside for slicing, use launcher to push forward cornmeal from last launch to force a burn out (15 seconds)

6) go to step 1

3-4 oven minutes / pizza or 15-20 pizzas / hr / oven

Most expensive part is the real mozzarella cheese which is outrageously expensive in the US. In France its 1/4 the price. I think I may make mozzarella in the near future, it looks like the easiest of cheeses.

Re:The Physics of baking good Pizza (2018) by AlbertCory on Wednesday December 21, 2022 @06:44PM (#34087897)
> real mozzarella cheese which is outrageously expensive in the US

do you mean the "fresh" stuff they sell in some US stores, in liquid? Or the bufalo?

I actually did a 1/2 and 1/2 test with a friend, half bufalo mozz & half standard shrink-wrapped mozz. He preferred the bufalo, I was meh.

The interesting thing was, the bufalo had so much moisture that it soaked through the crust. At least the shrink-wrapped stuff is dryer so you don't have that problem.

Re:The Physics of baking good Pizza (2018) by peteradio on Wednesday December 21, 2022 @06:53PM (#34087969)
Pardon me I meant the "fresh" stuff they sell in US stores is outrageously expensive, ~$10/lb. I don't really know what Bufalo is but the stuff I'm talking about would be fairly moist too, you need to use the cheese sparingly or else it will create a puddle on the surface.
Re:The Physics of baking good Pizza (2018) by AlbertCory on Thursday December 22, 2022 @12:27AM (#34090142)
Italians may use mozz made from water buffalo milk. I guess I spelled it wrong: two f's:

https://www.delightedcooking.com/what-is-buffalo-mozzarella....

I don't think it's very often used in the US.

Re:The Physics of baking good Pizza (2018) by graycat on Thursday December 22, 2022 @09:25AM (#34093534)
The mozzarella cheese I use is from Sam's Club. I just checked, and what I use is

"Maker's Mark Part Skim Shredded Mozzarella Cheese (5 lbs.)

$14.67 $2.93/lb"

Soooo, a lot less than $10/pound!

What if anything that Maker's Mark cheese has to do with anything from/in Italy, I don't know!

To have the cheese keep without mold, I keep it frozen. When I'm making a pizza and put on the mozzarella, it is still frozen. Right, when the heat for the cooking starts, still frozen! Works fine! The Teflon sheet lets the top of the pizza and the cheese get hot before burning the bottom of the crust.

In the US, pizza, in all its versions, is a big industry, a significant part of the diet of 300+ million people. BIG!

So, we're not talking a grandmother in a rustic kitchen in the hills of a small, rural town in Italy!!!

I omitted but might include: For applying the heat, I put the cast iron frying pan, covered, on one of the large burners of my 4 burner US electric stove. The burners are, as I recall, from GE or some such -- some big US company anyway. And I've seen them from the same source on other electric stoves. Soooo, if you have an electric stove, there's a good chance you have the same burner elements.

Then for the burner there is a dial. Viewing the dial as a clock face, 12 o'clock is OFF. 1 o'clock is the highest power. 6 o'clock is medium power. For cooking pizza, I use about 8 o'clock and 22 minutes. Then the toppings are hot. The cheese is melted. The crust is cooked with the edges puffy. And the bottom of the crust is browned but not burned. 23 minutes can be too long, burn the bottom crust and have the melted cheese running over the sides of the crust. 20 minutes, maybe the cheese is not yet melted. On your stove, likely you should watch carefully until you have the time and temperature about right!

Re:The Physics of baking good Pizza (2018) by AlbertCory on Thursday December 22, 2022 @05:27PM (#34099718)
Excellent, thanks.

For the cheese: yes, there's the freezer, but I've also found my Zwilling vacuum unit works well. Put the leftover in the special bag, evacuate the air (as much as it'll do, anyway), and I don't get mold on it.

Re:The Physics of baking good Pizza (2018) by AlbertCory on Wednesday December 21, 2022 @03:08PM (#34085741)
Thanks. The Serious Eats recipe for New York Pizza also does a test of the food processor vs. the stand mixer. The food processor beats the hell out of the mixer.