News for hackers. Stuff that matters.
Re:O.mg Cable by hinkley on Thursday September 02, 2021 @02:39PM (#28395725)
My school had a way to keep peripherals from wandering off, but if all you need to do is swap the cables then I’m not sure that would still work. Wrapping the cables into a wiring loom makes that process slower, assuming the loom is complicated enough. Did you ever use heat shrink? Or locking cable ties?

What the school did was run a steel cable behind the desks, then put a loop of the mouse chord through a steel washer and ran the security cable through all the loops. If you secure both ends you can’t get the cables separated even with slack.

The trick is that the hole in the washer had to be smaller than the connector so you couldn’t fish it back through no matter how much slack you get. That could still work for USB-A, but these days the connectors are getting smaller than the diameter of curvature of the cable, so you’d break it trying to do this. And on many peripherals you could destroy the chord without reducing the value of the device. One could cut the cable and install this Trojan one on many devices these days, the only telltale would be that the cable isn’t routed properly, which might be harder to notice immediately.

Re:O.mg Cable by lrvick on Thursday September 02, 2021 @03:23PM (#28396227)
On most keyboards and mice the cables are not soldered on the inside but just a quick connector.

You can get a female/male versions of this connector placed on either side of an attiny85 for a quick solderless implant no one will ever see.

Then just undo 2 screws, plug your implant inside the mouse/keyboard, screw it back.

To make this harder intentionally strip the screws with a drill, understanding you will never be able to repair that unit again.

Re:O.mg Cable by a1369209993 on Thursday September 02, 2021 @04:46PM (#28397146)
> To make this harder

Or, y'know, open it up and solder the connecter together (or remove the connector and solder the cable wires directly).

Re:O.mg Cable by hinkley on Thursday September 02, 2021 @07:12PM (#28398514)
My anecdote was a bit old and I’m certain some of those devices had soldered cables, meaning that a sheared wire couldn’t be handled by buying a new chord or combining parts of two mice. Because I specifically looked for that a few times with no luck.

But they’re right, these days when you crack open things you often find a connector soldered to the motherboard and the cable is merely plugged in. I think it’s just easier to manufacture. Pick and place, bulk solder and then a machine to plug in the cable, fast as you like, maybe with a loop in it as a poor man’s strain protector.

Re:O.mg Cable by a1369209993 on Friday September 03, 2021 @02:10AM (#28400945)
> meaning that a sheared wire couldn't be handled by [...] combining parts of two mice.

Well, if you're stealing them, you only need parts from one mouse: cut the cable close to the mouse, untangle it from whatever crap it's locked to, take mouse and cable home with you, disassemble mouse, feed cable back though (I think it's called) grommet, strip cable, pick out wires, solder wires to approriate mouse internals, reassemble mouse, done. You have a working mouse with only slightly shorter cable than before.

The point of using soldered cables for security is that setting up a soldering iron near a computer is conspicuous, so you get caught if try to install a attiny85 inside the mouse that way. You can still steal stuff just fine.

Re:O.mg Cable by victorhooi on Thursday September 02, 2021 @05:19PM (#28397486)
When you say strip the screw - do you mean strip the screw head, by drilling out the head?

That's evil...

(Or do you know some way to strip the thread itself).

Re:O.mg Cable by lrvick on Thursday September 02, 2021 @07:15PM (#28398536)
Yeah just intentionally drill the head so those screws are not coming out again without power tools which should be obvious in the open where they are deployed.

Or just epoxy the whole thing together.

Re:O.mg Cable by IIsi50MHz on Thursday September 02, 2021 @04:36PM (#28397022)
Seems there are special drill bits for removing stripped screws…
Re:O.mg Cable by lrvick on Thursday September 02, 2021 @07:18PM (#28398563)
If you can get away with using a drill on a keyboard and mouse covertly, I want to watch.
Re:O.mg Cable by ioseph on Thursday September 02, 2021 @05:37PM (#28397692)
Few strokes of a hacksaw and a rubber band (for grip). Or just some pliers
Re:O.mg Cable by mhb on Thursday September 02, 2021 @07:18PM (#28398568)
Good luck with those and that size screw.
Re:O.mg Cable by mhb on Thursday September 02, 2021 @07:17PM (#28398551)
Epoxying the screws in might be easier?
Re:O.mg Cable by hughrr on Thursday September 02, 2021 @02:42PM (#28395760)
All the cables were terminated inside the box and strapped every 1 inch with cable ties. Nothing was exposed that could be disconnected other than the monitor IEC lead.