News for hackers. Stuff that matters.
Re:Apple iPhone charger teardown: quality in a tiny expensiv... by andrewmcwatters on Tuesday August 03, 2021 @04:30PM (#28053762)
How does one learn to build such things? Most would say school, but I imagine there are particularly good reads out there that are more helpful to those driven enough to be autodidacts.

Thank you for such an excellent and digestible article. Such a pleasure to read.

Re:Apple iPhone charger teardown: quality in a tiny expensiv... by kens on Tuesday August 03, 2021 @04:34PM (#28053811)
I don't know how to build them, just take them apart :-) But seriously, there are a lot of books on switching power supply design. E.g. Fundamentals of Power Supply Design by Mammano, who is "the father of the PWM controller IC industry".
Re:Apple iPhone charger teardown: quality in a tiny expensiv... by seltzered_ on Tuesday August 03, 2021 @10:27PM (#28056534)
Huh, that's a new one. I worked in the space and Erickson and Maksimovic - Fundamentals Of Power Electronics (along with the courses taught at UC Boulder) was one many centered around. In many cases most of the power engineers I worked with just sorta had a feel for things and relied on simulation tools (LTSpice / SwitcherCAD).
Re:Apple iPhone charger teardown: quality in a tiny expensiv... by andrewmcwatters on Tuesday August 03, 2021 @04:37PM (#28053842)
Very cool! Thank you!
Re:Apple iPhone charger teardown: quality in a tiny expensiv... by cogman10 on Tuesday August 03, 2021 @04:36PM (#28053835)
For something as basic as a charger, an intro to electronics course/book is probably good enough. There's more than enough youtube videos out there about bridge rectifiers and the like.

The charge circuitry here isn't anything too special.

Re:Apple iPhone charger teardown: quality in a tiny expensiv... by lmilcin on Tuesday August 03, 2021 @08:08PM (#28055818)
Far from it.

Chargers are actually very complex and demanding design tasks with a lot of interesting* fault modes.

(* assuming you like small fires and exploding devices)

Just because you can make it work doesn't mean it is safe. Good charging circuit will be designed to behave correctly if any of the components fail.

Even a simple battery charger can easily cause fire.

The usual advice to amateurs is to stay away from charging circuits and switching power supplies. And reuse existing circuits in their designs. There is a lot of complete charging circuits and power supplies made to be included in designs.

Re:Apple iPhone charger teardown: quality in a tiny expensiv... by dontcare123 on Wednesday August 04, 2021 @05:09AM (#28058845)
This isn't an actual charger though, just a basic off the shelf switching power supply, low power AC -> 5V DC. The actual battery charger chip is on the phone (which again, will use a ready made BMS IC, so not really complicated either, all the smarts are already done).

There's some things to consider when laying out a switcher (keep loop areas small, keep sensitive lines from noise ones, etc), but it's not that complicated, and once you've done a few of them, it becomes routine. And of course to pass safety standards there are clearance and creepage rules and EMI/EMC to keep in mind.

Any junior level EE/hobbyist with a few years of tinkering should be able to put this together.

Re:Apple iPhone charger teardown: quality in a tiny expensiv... by kens on Tuesday August 03, 2021 @04:47PM (#28053972)
It's easy to make a linear power supply, but a switching power supply like a charger has a lot of complications. Among other things, the layout of the board matters a lot due to the high frequencies involved. I'll point out the the application note on this controller chip is 34 pages long. https://www.st.com/resource/en/application_note/an1326-l6565...
Re:Apple iPhone charger teardown: quality in a tiny expensiv... by cogman10 on Tuesday August 03, 2021 @04:53PM (#28054055)
Certainly. My point was more that the basics are pretty readily covered in intro electronics courses. Heck, throw in a low pass filter or two and you end up with a lot of the same required knowledge to make a switching power supply.

I agree you won't be able to make an apple quality device, it'd just be enough info to understand how one is working (Without taking into account things like line noise impact on wiring).

Re:Apple iPhone charger teardown: quality in a tiny expensiv... by andrewmcwatters on Tuesday August 03, 2021 @04:39PM (#28053874)
I imagine then that some of the more claimed sophisticated elements come from multidisciplinary backgrounds like having experience with electronics in noise-sensitive circuitry.