In the mean time I use a 1/2" steel plate in my home oven. Our oven goes up to 550F and the plate can hit ~650F under the broiler. Still a long ways from 900F but it can bake a very decent pizza in 3-4 minutes, with minimal heat loss (heat loss would be more of an issue with a thinner plate, I assume).
Also no worries about cracking if a launch goes badly and I end up with sauce leaking off the pizza--I broke quite a few pizza stones that way.
Having said that, it does take a significant amount of the trunk, so.. meh.
It was a bit dense for me in parts, but isn't it a very standard bread cooking trick to stick a cast iron pan in the oven to give it more thermal mass?
I'm also quite curious about these cooking temperatures, I know I'm never going to hit those in my electric stove, and I do cook deep dish pizzas longer at a lower temperature so they aren't goopy dough on the bottom. I wish I could try cooking them hotter, they still come out like crackers at 475F sometimes.
I'm curious, regarding your note about pizza stone temperature, do you make the pizza dough stretched and topped and then... put it on the already hot stone? How do you get the dough from the place you topped it to the stone without it falling to pieces?
What kind of stone could it be that a cast iron pan wouldn't be both higher thermal conductivity and also higher heat capacity? Are you using temperatures too high for cast iron?
There are plenty of demos and tips on "how to launch a pizza"
e.g.
https://www.youtube.com/watch?t=153&v=_3jAnfvriCE&feature=yo...
https://www.youtube.com/watch?v=VkD-IrTNpTk
https://www.youtube.com/watch?t=153&v=n8F8YdxA5jA&feature=yo...
> Are you using temperatures too high for cast iron?
No, not at all. So why not use cast iron?
IDK, when cooking pizza inside a kitchen oven some people do use cast iron plates. They're a fair amount more expensive than the ceramic "pizza stone", and heavier, apparently they work very well. google "pizza steel".
In a custom-made pizza oven, ceramic floors are the only type I've seen. I guess iron just isn't necessary in this case? The whole interior gets heated up to 450-500C. If you're building a dome outdoors out of concrete and brick, then thermal mass is there because of regular mass?
Steel or iron in a 450C oven would burn the bottom of the pizza before the top was anywhere close to done. It works well in home ovens at much lower temperatures (say 250C).
I've been making pizza often since I was five, for many years weekly for dozens of people, and the center of the bottom is always the hardest to get cooked nicely without burning the top.
If this fixes that I can maybe avoid prebaking the crusts, that was my workaround previously. This sounds way better!
If you are cooking in your kitchen oven, you also have a second option: a sheet of baking parchment.
I like the idea of learning to launch it though, I'm already sad that I can't toss the dough without dropping it so that seems like a just slightly easier skill that depends more on getting the dough to the right consistency. Seems like it will be fun to do anyway.
If you are making pizza "weekly for dozens of people" then equipment such as pizza peels and/or a pizza oven might be ideal for you?
You use a pizza peel [1]. Put the pizza on the peel (some people put the stretched dough on and top it while it's on the peel, some people top it first and then transfer it to the peel), put it in the oven, and then slide the peel out from underneath.
Flour/semolina or corn meal helps keep the pizza dough from sticking to the peel.
It’s much cleaner than the way I used to do it, which required cornmeal and often resulted in crooked transfers, misshapen dough, and lopsided toppings.
There isn't. There are 3 operations: launch, turning and extracting, and different styles of peel are "best" for each.
A smooth wooden peel (or perforated metal) is good for launch.
A "turning peel" is a thing, smaller and rounder.
A metal peel is best for extracting - don't use your launch peel, you don't want it to get hot, or the next pizza will stick.
This guy covers some of it: https://youtu.be/n8F8YdxA5jA
Edit: As other similar response mentioned peel seems to be the more specific word for paddle.
cast iron pans are great, but a pizza stone can be much thicker than a skillet, so you can get a lot more heat capacity. not sure about the conductivity, but some "stones" are made of steel anyway.
Currently on a Koda-16 which gets up to 900f in about 20 mins, yet is so well insulated - 45 minutes later there’s still snow sitting on top of it. A pizza usually takes about 90-120 seconds for me.
The thermal mass is important - the pizza stone at the bottom on this model is thicker than my last one, and while I could cook several pizzas, the ones in the middle took longer because I didn’t let the stone heat up again after the last pizza. Noticeable difference if there was no “rest time” between pizzas. Some friends have tried “metal pizza stones” which also retain heat really well (like 1/4” steel plate type of thing) apparently works well in hone ovens.
I use mine also to sear sous vide steaks. Works out fantastic.