> I see a lot of DIY posts that are probably not 100% the same thing but are they even close?
I have yet to see (though I haven't looked extensively) a DIY ventilator that has the fine tune control many doctors are suggesting are required for COVID patients.
My understanding is most of the DIY vents are comparable to emergency or transport vents. They'll keep a patient breathing for minutes/hours until they can be transferred to a proper ventilator. After a short period of time, you really need to transfer a patient to a proper ventilator to continue to support life.
Two big challenges with COVID patients in particular:
* They require ventilation for DAYS or even weeks. Over durations of that long, you really need precise control over a vent. A tech analogy is using floating point numbers for finance. Over a small number of transactions, a floating point number may be sufficient. Over time, though, the inaccuracies of floating point numbers will become apparent.
* Many COVID patients needing ventilation also have Acute Respiratory Distress Syndrome (ARDS). The simple explanation is their lungs are functioning so poorly that you can't simply stuff oxygen into them and hope it works. You need to be extremely particular with how you control breathing.
* Bonus, related to point two, many doctors are reporting using pretty crazy ventilation settings as a baseline. They're basically overclocking a CPU/GPU by default then hoping they can keep overclocking as CPU/GPU load increases (not fully accurate, but it's an analogy).
Ventilators turn out the be pretty complicated.
Here's a useful thread: https://twitter.com/aroradrn/status/1243091107149418496
And another simplified cheat sheet for people who use machines in one setting which are now being used in other settings, but it has replies from doctors asking questions that give some hints at the complexity: https://twitter.com/aroradrn/status/1244134454001635329?s=20
Then you have all the "human factors" stuff caused by machines having different layouts.
This is going to be a huge issue with the onslaught of different manufacturers.
I liken it somewhat similar to helping troubleshoot router/switch issues... yes at a high level they're all the same but, at the same time, each one has it quirks and peculiarities and even use slightly different nomenclature that make it a non-trivial exercise.
People can survive at high altitudes, which will see pressure of 70% sea level (or less, especially when considering mountain climbing). Additionally, when SCUBA diving, something like 30 feet of depth = 1 atmosphere.
I feel like I'm missing something here. Any ideas?
I know a bit about scuba diving, and you absolutely are not supposed to go diving if you have a lung injury.
I would speculate that if you put a person with serious covid on a mountain top or 30 meters under the ocean it would kill them pretty quickly..
The pressure that must be narrowly controlled in a ventilator application is the relative pressure: the difference between the absolute pressure outside the lung (in the room) and the absolute pressure inside the lung. This relative pressure is what does all the work --- mechanically opening airways and alveoli --- and could cause all the injury.
Increasing pressure with depth does increase work of breathing due to higher gas viscosity. Beyond a certain depth, divers can no longer ventilate enough to take in O2 and remove CO2. This problem can be mitigated to an extent by breathing lower density gasses such as helium. Occasionally hospitals even have patients with severely impaired lung function breathe heliox just to get better gas flow.
In theory it's possible to use a 2nd-stage scuba regulator as an improvised mechanical ventilator by partially blocking the exhaust valve with your hand and pressing the purge button. In practice it's unlikely to work, but if I was trying to rescue someone who had stopped breathing in the water and had no way to get them back to shore or a boat quickly then I might try it as a last-ditch effort.
That's because the pressure outside their body is the same as inside.
With a ventilator, the pressure going in is higher than atmospheric pressure. That can cause damage.
This opens up a bigger question too, is there such a thing as a path for open source medical devices to be built and certified and deployed? Is there a company that supports something like this? I follow Scott hanselman, a Microsoft employee who’s diabetic, and there is a big movement within that community to build open source artificial pancrea, using insulin pumps and software and such. Is there a play like that for ventilators? And other critical medical devices?