News for hackers. Stuff that matters.
Re:Why the Boeing 737 will never take the place of the 757 by WalterBright on Sunday November 10, 2019 @03:57AM (#21497162)
> Did they want the extra 10% buffer for any particular reason?

They said they just were more comfortable with more margin. The stress group was an independent organization to avoid conflicts of interest with the design group. Our job was to design, their job was to verify. If parts broke, they got the black eye. If the airplane was overweight, design got the black eye. We both had to agree, and it was a system that worked well.

Most design engineers didn't work out the stresses themselves, they just hoped to pass the stress group. It was pass/fail for them. In my not so humble opinion, they were making overweight parts. I was interested in using math to sculpt perfect parts :-)

For example, the inside diameter of the jackscrew was specified to the ten-thousandth of an inch, something like 2.1834..2.2096. So I'd get the "why not make it a nice round 2.19..2.20?" I'd reply because if it came in at 2.205, it would get rejected, even though it was perfectly usable. And I got my way, because the jackscrew forging was a very, very expensive part and rejecting a usable part did not make anyone happy.

(Rejected expensive parts often got bounced back to engineering to find a way to salvage them. I just was doing the math in advance so they wouldn't have to.)

Re:Why the Boeing 737 will never take the place of the 757 by Calloutman on Sunday November 10, 2019 @05:18AM (#21497368)
That specification is to 2.5 micron accuracy. Surely the forging can't be made to that precision?
Re:Why the Boeing 737 will never take the place of the 757 by WalterBright on Sunday November 10, 2019 @03:49PM (#21500114)
> Surely the forging can't be made to that precision?

It's forged slightly oversized, then machined down to spec.

Forgings are about 3x stronger than a casting, and are of a more consistent quality, which is why when I increased the HP for my Dodge, I spent the extra bucks to get forged spinning parts (usually they are cast).

Re:Why the Boeing 737 will never take the place of the 757 by wbl on Sunday November 10, 2019 @07:03AM (#21497660)
The range is much larger: OP was just being very precise in expressing the range so the manufacturing process had some extra leeway.
Re:Why the Boeing 737 will never take the place of the 757 by brians on Sunday November 10, 2019 @10:01AM (#21498163)
I wonder what was measuring to that precision with such accuracy! It’s when I think about tolerances on the equipment that’s checking tolerances that I start getting dizzy and retreat to software for a bit.
Re:Why the Boeing 737 will never take the place of the 757 by Obi_Juan_Kenobi on Sunday November 10, 2019 @09:49PM (#21501749)
2.5 micron is basically the metric value for a 'tenth', i.e. one ten-thousandths of an inch. A typical machine shop will usually work in tolerances of a 'thou' or two, but most are equipped to measure to tenths without too much fuss. Standard micrometers have a vernier that reads tenths, and tenths indicators aren't uncommon.

Going beyond that, to tens of millionths or sub-micron, is where things get nutty with special climate controlled rooms. Digital indicators can easily read with such precision, but controlling for factors like radiated body heat become important.

Reference measurement is usually done with gauge blocks and pins. The development and popularization of these sets is basically how mechanical parts became standardized.

If you're interested in that sort of thing - bootstrapping precision and the like - check out "The Foundations of Mechanical Accuracy".

Re:Why the Boeing 737 will never take the place of the 757 by beerandt on Sunday November 10, 2019 @01:12PM (#21499251)
The precision (ability) of the machine rarely matches the precision of the measuring apparatus, if it's even part of the same equipment. And that's usually ok, even preferred, and cheaper.

If it's a rabbit hole you're interested in, then check out the history of geodesy / geodetic surveying & the design of mechanical / optical surveying equipment- especially theodolites & auto-levels (and even chronometers and astronomic observatories, if you want to go 4-dimensional).

It was the "industry" that had a large hand in innovating this technology, which led to the smaller versions used in manufacturing (made even more interesting due to the fact it was all funded to better artillery, and ultimately ballistic missle targeting, sans-GPS.)

I'd be happy to steer you in the right direction, if interested. It's a personal favorite.

Re:Why the Boeing 737 will never take the place of the 757 by bumby on Sunday November 10, 2019 @03:39PM (#21500067)
Possibly a coordinate measuring machine (CMM) in an environmentally controlled environment, but even then it's coming awfully close to the capability limits
Re:Why the Boeing 737 will never take the place of the 757 by dsfyu404ed on Sunday November 10, 2019 @09:56AM (#21498145)
The spec is almost certainly for the machining after it's been forged.
Re:Why the Boeing 737 will never take the place of the 757 by WalterBright on Sunday November 10, 2019 @03:52PM (#21500125)
I would have loved to take a field trip to Saginaw Gear and see all the various steps in its manufacture.
Re:Why the Boeing 737 will never take the place of the 757 by dsfyu404ed on Sunday November 10, 2019 @07:10PM (#21501110)
Like this but bigger.

https://www.youtube.com/watch?v=dzIsR4Mg158

"ball screw" and "lead screw" are your search terms. For aerospace it's gonna also be center drilled to save weight as well.

Re:Why the Boeing 737 will never take the place of the 757 by maxerickson on Sunday November 10, 2019 @10:13AM (#21498224)
The forged parts are likely machined (for better finish and tolerance).
Re:Why the Boeing 737 will never take the place of the 757 by RaptorJ on Sunday November 10, 2019 @12:32PM (#21499034)
I wonder if you guys all went on a field trip to watch The Wind Rises haha