News for hackers. Stuff that matters.
Re:Home Chip Fab by m0zg on Friday August 09, 2019 @06:57PM (#20658886)
Speaking of which, does anyone know where (in the US) I can safely dispose of ferric chloride, sulfuric acid, and hydrochloric acid? I used to etch my own boards years ago. And ever since then the spent stuff just sits in glass jars in a double plastic box in my garage. I don't etch anything anymore, and it's taking up space.
Re:Home Chip Fab by segfaultbuserr on Friday August 09, 2019 @07:10PM (#20658944)
> safely dispose of ferric chloride, sulfuric acid, and hydrochloric acid

The first step is easy: neutralize them with any base, such as baking soda. You don't need precision, just add a lot of it, and make sure the pH is close to 7 (or beyond, baking soda is not corrosive) at the end. After this step, the solution is no longer acidic or corrosive and much safer to handle.

Unfortunately, the next step is tricky. The solution is safe, but it still contains a lot of Cu+ ions, which is a heavy metal pollutant and poisonous.

On the other hand, if your sulfuric or hydrochloric acid is unused for etching anything (clean without those nasty ions), you are good to go, just dump them in the sink after you've neutralized them (test with pH paper) it's perfectly safe.

Re:Home Chip Fab by m0zg on Friday August 09, 2019 @07:50PM (#20659173)
Is this what people actually do? I mean I'm aware I could neutralize them, but Cu is still going to be in there and I still can't pour this stuff down the drain. Then there's ferric chloride which is just nasty stuff that will likely stain everything it comes in contact with. I just want to get rid of it in a fully environmentally safe way.
Re:Home Chip Fab by parsimo2010 on Friday August 09, 2019 @09:39PM (#20659636)
I'm not sure it is economical, but I had some Sodium Persulfate etchant that was full of copper and accidentally dropped a piece of steel in it. The copper plated onto the steel almost instantly. You could probably use iron filings (or some metal that won't dissolve in your acid) to pull most of the copper out of the acid, and then neutralize. I'm not sure what you would do with the solid copper after that. It might take some effort to get a system that was reliable and economical, but the basic idea of precipitating out the copper before neutralization should work.
Re:Home Chip Fab by marmaduke on Saturday August 10, 2019 @06:49AM (#20661329)
I don't think it's hard. My high school chemistry teacher did this, reusing the same copper every year. (I dont remember the details though)
Re:Home Chip Fab by segfaultbuserr on Friday August 09, 2019 @07:56PM (#20659208)
Don't ask me, I don't know, as I'm asking the same question. I'm waiting for some answers to my question: https://news.ycombinator.com/item?id=20659004
Re:Home Chip Fab by faissaloo on Friday August 09, 2019 @07:11PM (#20658950)
There are usually reactions you can do to make them safe to dispose of in a regular manner, you should be able to find them with a decent amount of googling.
Re:Home Chip Fab by asynchronous13 on Friday August 09, 2019 @07:14PM (#20658968)
pretty easy really. Add acid to water, then add baking soda to the acidic water until it's neutralized. (no more bubbling), then pour it down the sink with more water. Use appropriate precautions, gloves, goggles, well-ventilated area, etc. Once the acid is neutral, it won't hurt anything in the pipes.
Re:Home Chip Fab by segfaultbuserr on Friday August 09, 2019 @07:21PM (#20659004)
But is it acceptable to dump wastewater with Cu+/Cl- ions inside? I've read that according to some regulations in some areas, they are considered pollutants and should not be dumped directly to the drainage.

Or is it something you can just ignore, because at the end of the day everything goes to a wastewater treatment plant, and your volume/concentration is too low to be considered hazardous, and actually not more harmful than the wastewater of commercial chemical cleaners, and well within the wastewater processing capabilities for small volumes?

Can anyone give an authoritative answer to this question?

Re:Home Chip Fab by joshvm on Friday August 09, 2019 @10:28PM (#20659777)
The official advice is to keep neutralising it, collect the sludge and pour the waste water away.

https://www.mgchemicals.com/products/prototyping-and-circuit...

> The solution must not be put down the drain because of residual copper ions left in it. To make it safe for disposal, you can add sodium carbonate (washing soda) or sodium hydroxide to it to neutralize it, until the pH value goes up to between 7.0 and 8.0, testing it with indicator paper. Copper will be deposited as a sludge. Allow the sludge to settle, pour off the liquid, further dilute it with water and then it can be poured down the drain. Collect the sludge in plastic bags and dispose of it as required by your local waste authority.

Re:Home Chip Fab by kragen on Friday August 09, 2019 @08:01PM (#20659228)
Cl ions are fine; dissolved table salt consists of them, plus some cations. The copper is more of a problem, and I don't know the official answer. I'd think that if you could oxidize it to copper monosulfide (covellite), cupric oxide (tenorite), or even fully hydrated copper carbonate (malachite) if you don't have acid rain, that would adequately protect it from weathering and thus allow you to dispose of it safely. But it might be more practical, as well as legally safer, to electrolytically reduce it back to copper and sell it for recycling. Copper, as a semi-precious and semi-noble metal, is recycled actively everywhere the humans live.

I think the biggest problems for chip fabrication waste (not circuit board etching) are HF and nonpolar organic solvents. I'd think neutralizing HF with chalk would yield fluorspar, which is resistant to weathering even over geological timescales. But again I don't know what the official answer is. Maybe dumping fluorspar in your yard will get you arrested.

Re:Home Chip Fab by hinkley on Friday August 09, 2019 @09:37PM (#20659622)
First warning with neutralizing acids: You're going to release a lot of heat, make sure you have a large thermal mass to absorb it. Someone else mentioned mixing your ingredients with water first. This is why.

From what I understand the last thing you want to experience is an explosion of hydrofluoric acid.

The internet seems to suggest lime (->fluorspar) or soda lye (->NaF, used for fluoridating water) to neutralize HF, but that's two other substances you wouldn't want raining on your head... be careful out there.

Re:Home Chip Fab by droithomme on Friday August 09, 2019 @11:04PM (#20659888)
Yeah if you just dump a base into these strong acids things go foom! and you end up with dead makers.

Don't mix this stuff in dilution in an enclosed space either as the H2 gas can create another explosion hazard.

Re:Home Chip Fab by kragen on Saturday August 10, 2019 @01:17AM (#20660331)
HF is technically a weak acid, but I wouldn't venture to neutralize it quickly; it's very reactive even if it doesn't fully dissociate in water.

As for hydrogen, neutralizing acids with bases doesn't generally produce it, but ventilation is still a good idea.

Re:Home Chip Fab by kragen on Friday August 09, 2019 @11:02PM (#20659877)
Why wouldn't you want fluorspar raining on your head? Just because it's heavy and hard?

I suggested fluorspar rather than NaF because a backyard full of fluorspar is a pretty rock garden, while a backyard full of NaF is a toxic waste dump.

Re:Home Chip Fab by droithomme on Friday August 09, 2019 @11:01PM (#20659876)
Cl's in toilet cleaner. Dilute is not a problem.

Cu though is an aquatic herbicide (used to rid decorative ponds of all plant life including algae) and can mess up things.

> at the end of the day everything goes to a wastewater treatment plant

Some of these things, especially the photosensitive chemicals in particular ammonium dichromate will annihilate the wastewater treatment plant. Experienced this problem in an industrial context once, resulting in tens of millions of dollars in damages to taxpayers and a giant fiasco. As a result our privileges to use the municipal sewage system were withdrawn and we had to spend tens of millions in evaporation towers since no water could leave our facility ever again.

Re:Home Chip Fab by muricula on Friday August 09, 2019 @07:18PM (#20658988)
The concern probably isn't the acidity, but the heavy metals and other toxins in the solutions. Pouring tpxins down the drain isn't a good idea.
Re:Home Chip Fab by hinkley on Friday August 09, 2019 @09:40PM (#20659639)
Yeah it's being talked around in this thread but I think most of the participants seem to get it.

The solvents can be broken down to things that are compatible with the sewer system.

The hard part to deal with is the material you dissolved with the solvent.