News for hackers. Stuff that matters.
Re:A novel brewing process via controlled hydrodynamic cavit... by theptip on Tuesday September 27, 2016 @12:54AM (#12587508)
Some points that are interesting to me, and warrant further investigation:

1) Milling of malts is no longer required. As a microbrewery operator, now I don't need to come in the day before to run the mill for a planned brew. Massive win on scheduling and convenience.

2) "Concerning mashing and sparging, the new equipment allows to eliminate sparging altogether since the pulverization of cavitating malts ... prevents practically any starch to remain trapped into the grains". Again, from a microbrewery operator's perspective, another few hours of labour saved per brew, since I don't have to run a few sparges over my grain.

3) Since cavitation apparently sanitizes the wort, we don't need to do a boil. This saves another 1.5 hours on a brew, removes the need for a boil vessel, and some other equipment in my brewery (steam boiler to heat the boil vessel, a bunch of plumbing for said steam).

4) related to 3, the hops can be isomerized without boiling. I've had great success with low-boil techniques like the hop stand, so I'd assume that CHC beer would capture a lot more of the volatile aromatics from hops. This could lead to some great IPAs.

I'd love to figure out what the MVP is for this rig, and whether it could be replicated at homebrew scale, as it seems to simplify the process massively.

Re:A novel brewing process via controlled hydrodynamic cavit... by hyperbovine on Tuesday September 27, 2016 @11:05AM (#12590117)
Plus just general water savings. Between sparging, boil off and cleanup I've felt pretty bad about brewing in drought-stricken California in the last few years. Also, I'm strictly an amateur brewer, but I thought that the boil had other useful features? (For example, eliminating chlorine.) Do you filter the water ahead of time?
Re:A novel brewing process via controlled hydrodynamic cavit... by theptip on Tuesday September 27, 2016 @06:23PM (#12593726)
Where I am the water is very soft, and only lightly chlorinated, so I do not filter. (I do add minerals to improve the mash efficiency and yeast health though). If your water has lots of Chlorine (not Chloramine) then the boil will drive this off, but you might be better off starting with Reverse Osmosis water to get a clean slate, and then adding all the minerals you need.

Another important reason for the boil is driving off DMS (which causes a cooked corn off-flavour).

The paper covers both of these, I think:

"Due to the strong liquid degassing properties as a result of hydrodynamic cavitation processes (Clark, Dewhurst, Payne, & Ellwood, 2001; Gogate & Pandit, 2011; Iben, Wolf, Freudigmann, Fröhlich, & Heller, 2015; Senthil Kumar, Siva Kumar, & Pandit, 2000), undesired volatile aromatic compounds are safely expelled after few minutes of cavitation"

Sounds like this would apply to the volatile chlorine as well, but I'm not certain about that.

Also sounds like this should be more rigorously tested, as I don't see anything by way of data to back up this claim; perhaps the cited papers explain more.

[dead]
Re:A novel brewing process via controlled hydrodynamic cavit... by elktea on Tuesday September 27, 2016 @05:20AM (#12588290)
LED is bad?
Re:A novel brewing process via controlled hydrodynamic cavit... by mrob on Tuesday September 27, 2016 @07:26AM (#12588724)
LEDs often emit more blue spectrum light than older technologies, which makes them more effective at stopping melatonin production. See: https://en.wikipedia.org/wiki/Intrinsically_photosensitive_r...

LEDs also switch much faster than older lights, which means people can pulse-width modulate them, causing annoying flicker for people who're sensitive to it.

Admittedly both these problems are avoidable, but in practice they're seen as LED problems because they're so common with LEDs.